İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
Woody

Oluşturan

Woody

13. Kasım 2026NO
9
0
0
0
0

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)

A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
Başlangıç
About 3 hours

Talimatlar

1

His sizes in centimetres

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3

Cut the staff and loop

Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.

Bu adım için malzemeler:

Bambu sırıklarBambu sırıklar1 adet
Koşum derisiKoşum derisi1 adet
Bakır perçinlerBakır perçinler1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Deri bıçağıDeri bıçağı
El matkabıEl matkabı
ÇekiçÇekiç
Şerit MetreŞerit Metre
4

Make and fix the snow disk

Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Gomalak vernikGomalak vernik1 adet
Demir telDemir tel1 adet
Tel kroşeTel kroşe4 adet

Gerekli aletler:

Kıl TestereKıl Testere
Kol matkabı ve ucuKol matkabı ve ucu
El matkabıEl matkabı
Yassı Ağızlı PenseYassı Ağızlı Pense
ÇekiçÇekiç
Geniş boya fırçasıGeniş boya fırçası
5

Set the spike

Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Demir telDemir tel1 adet
Kurşun KülçeKurşun Külçe1 adet
Jüt sicimJüt sicim1 adet
BalmumuBalmumu1 adet

Gerekli aletler:

El matkabıEl matkabı
Marangoz keskileriMarangoz keskileri
Metal kepçeMetal kepçe
Propan PürmüzPropan Pürmüz
Eğeler (El Eğesi)Eğeler (El Eğesi)
Yassı Ağızlı PenseYassı Ağızlı Pense
6

Troubleshooting

Ski staff troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.

Malzemeler

11

Gerekli Aletler

13

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...