İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Closet Shoe Rack: Wedge-Shaped Pockets on the Wall With a Slatted Bottom for Dirt to Fall Through (Boy Mechanic, 1913)
A shoe rack "that can be placed on the wall in the clothes closet", from The Boy Mechanic (1913): two boards 9 in wide and about 3 ft long, held apart by six wedge-shaped partitions so the pockets open wider at the top, and a slatted bottom that lets the dirt fall through. Sizes are the book's.
Contributed to Popular Mechanics by Guy H. Harvey of Mill Valley, California.
Başlangıç
About 2 hours
Talimatlar
1
1
The partitions
The partitions
Jupyter defteri yükleniyor…
2
2
Read The Boy Mechanic
Read The Boy Mechanic
"Two boards, 9 in. wide and about 3 ft. long, with six partitions between, as shown, will make pockets about 6 in. long. The width of the pockets at the bottom is 2 in. and at the top 5 in."
3
3
Cut the boards and partitions
Cut the boards and partitions
Cut two pine boards 9 in wide and about 3 ft long, the back and the front. Cut six partitions as wedges from the notebook, 9 in tall, 2 in deep at the bottom and 5 in at the top.
Bu adım için malzemeler:
Çam tahta1 adetGerekli aletler:
Şerit Metre
Kurşun kalem
Marangoz gönyesi
El Testeresi4
4
Assemble the pockets
Assemble the pockets
Nail the partitions to the back board, square to it, one at each end and the rest spaced about 6 in apart. Nail the front board to their sloping edges, so it leans out and the pockets open wider at the top.
Bu adım için malzemeler:
Çiviler1 adetGerekli aletler:
Marangoz çekici5
5
Fit the slatted bottom
Fit the slatted bottom
Nail strips across the bottom of the pockets with gaps between them, as his Fig. 1, so the dirt from the shoes falls through.
Bu adım için malzemeler:
Sert ağaç çıtası1 adet
Çiviler1 adetGerekli aletler:
El Testeresi
Marangoz çekici6
6
Hang it
Hang it
Screw the back board to the wall of the clothes closet (ours), and put a pair of shoes toe-down in each pocket.
Bu adım için malzemeler:
Ahşap vidalar1 adetGerekli aletler:
El matkabı
Tornavida takımı7
7
Troubleshooting
Troubleshooting
Shoe rack troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From **The Boy Mechanic, Volume 1**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913 (Project Gutenberg #12655), "Homemade Shoe Rack", contributed by Guy H. Harvey of Mill Valley, California. The board sizes, pocket sizes and six partitions are the book's; the wood, nails, slat sizes and hanging screws are ours.
Malzemeler
4- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
7- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


