İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)
Woody

Oluşturan

Woody

13. Kasım 2026NO
6
0
0
0
0

Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)

R. H. Allen's four-passenger coasting bob from The Boy Mechanic, Book 2 (1915): a 6-1/2 ft top board with four hinged seat backs, carried on two short sleds with ash runners shod in 5/8 in round iron. The rear sled rocks on a wedge and hinges to follow the ground; the front sled steers by a broom-handle post and a wheel made from a nail-keg hoop. Every size is his.
Orta
About 3 days

Talimatlar

1

His list of materials in centimetres

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

"Any wood may be used for the sled, except for the runners, which should be made of ash." His list of materials: 1 top 6-1/2 ft x 16 in x 1-1/4 in; 4 runners 22 x 4 x 1 in; 4 crosspieces 16 x 3 x 1 in; 3 pieces 16 x 5 x 2 in; 1 piece 16 x 5 x 1 in; 1 shore 16 x 3 x 1 in; 4 seat backs 12 x 16 x 1 in; 1 dowel 3 ft x 1 in; 4 rods 5/8 in x 30 in; 4 eyebolts 1/2 x 6 in; 3 hinges 5 in strap; 8 hinges 3 in strap.
3

Shape and shoe the runners

Cut one ash runner to shape and use it as the pattern for the other three. Cut a groove about 1/4 in deep along the under edge to take the curve of a 5/8 in round iron rod. Bend each rod to fit in the groove, up the back of the runner and over the top at the front; flatten the ends and drill two holes in each for wood screws (a blacksmith can flatten them, he says). Screw the irons on.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Yuvarlak demir çubukYuvarlak demir çubuk4 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kıl TestereKıl Testere
Marangoz keskileriMarangoz keskileri
Kömür ocağıKömür ocağı
ÖrsÖrs
Demirci çekiciDemirci çekici
Tezgah MengenesiTezgah Mengenesi
El matkabıEl matkabı
Kurşun kalemKurşun kalem
4

Build the two sleds

Notch the top edges of each pair of runners for the 16 x 3 in crosspieces, near the ends, so the crosspieces lie flush with the runner tops and the notches of each pair line up. Fit them snugly, fasten with long, slim wood screws, and stiffen each joint inside with a small metal brace.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Ahşap vidalarAhşap vidalar1 adet
Köşe gönyesiKöşe gönyesi8 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
El matkabıEl matkabı
5

Make the rocking rear joint

Cut a heavy 2 x 5 in crosspiece sloping across its width, from 2 in thick at one edge to a feather edge at the other. Fix the three large strap hinges to the sloping face, and fasten the piece solidly on the rear sled's runners with its centre 8 in from their front ends. This lets the rear sled rock but not turn sideways.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Demir şerit menteşeDemir şerit menteşe3 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
El rendesiEl rendesi
El matkabıEl matkabı
6

Mount the front sled crosspiece

Fasten the supporting crosspiece on top of the front sled's runners with its centre 11 in from their front ends.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El matkabıEl matkabı
Şerit MetreŞerit Metre
7

Brace the top board

Round both ends of the top board and plane it smooth. Underneath, fit two crosspieces, each with two 1/2 in holes bored through its width near the ends for the eyebolts: one with its centre 12 in from the rear end, the other 8 in from the front. Screw them on. Set the shore in the centre of the board, run wires over it between the eyebolts, and draw the eyebolts up until the wire is taut over the shore, so the long board cannot sag.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Halkalı cıvataHalkalı cıvata4 adet
Demir telDemir tel1 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
El rendesiEl rendesi
Kol matkabı ve ucuKol matkabı ve ucu
Şerit MetreŞerit Metre
8

Fit the seat backs and foot rests

Round the top corners of the four backs and cut the bottom ends at a slight angle for a slant. Hinge them to the top board with the small strap hinges every 18 in, starting at the rear. Bore 1 in holes about 1 in deep in the edges of the top board every 18 in, beginning about 5 in from the front, and drive in pins 4 in long cut from the dowel, as foot rests.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Demir şerit menteşeDemir şerit menteşe8 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Şerit MetreŞerit Metre
9

Make the steering

Cut a broom handle to 18 in and fasten one end in a hole bored centrally in the 5 in crosspiece of the front sled. Bore a hole in the top board through the centre of the crosspiece underneath; put two metal washers on the stick and run it up through the hole, then fasten a hardwood collar to it just above the board so the top cannot lift off the sled. For the wheel, fasten a piece of wood across a nail-keg hoop, cover the hoop with garden hose and wrap it with twine; bore the centre of the crosspiece to fit the broom handle and screw it on.

Bu adım için malzemeler:

SüpürgeSüpürge1 adet
Düz PulDüz Pul2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Demir kasnakDemir kasnak1 adet
Kauçuk hortumKauçuk hortum1 adet
Jüt sicimJüt sicim1 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
El matkabıEl matkabı
10

Join the sleds and fit the ropes

Fasten the rear sled to the top board with screws through the free wings of the hinges into the crosspiece. Bore holes in the front ends of all runners and attach a chain or rope: the rear one's loop to the underside of the top board, the front one for drawing the sled.

Bu adım için malzemeler:

Ahşap vidalarAhşap vidalar1 adet
Demir zincirDemir zincir1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
El matkabıEl matkabı
11

Troubleshooting

Bobsled troubleshooting.

Flow

Loading...
12

History and honest limits

From "Four-Passenger Coasting Bobsled" by R. H. Allen, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 24-26). The runner shape comes from his drawing, not from figures. The scan calls the steering collar a hardwood collar; the Gutenberg text drops "hardwood". The tools and metric figures are ours.

Malzemeler

15

Gerekli Aletler

12

Bu planla yapılan

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...