İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)
Woody

Oluşturan

Woody

13. Kasım 2026NO
9
0
0
0
0

Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)

The first lesson of Chas. M. Miller's reed-furniture series in The Boy Mechanic, Book 2 (1915): a basket 5 in across and 3 in high, woven on a bored basswood bottom. The spoke ends are turned into a roll that hides the wooden edge, the side is triple-woven, and the top is finished with a break-down border.
Başlangıç
About 3 hours

Talimatlar

1

His sizes, and the spoke spacing

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

"The center is the most difficult part of the basket making, and it is best to begin with wood bottoms." The reeds placed vertically are called spokes, the horizontal ones weavers.
3

Make the bottom

On a board about 6 in square, 1/4 in thick (basswood is best, pine or cedar will do), draw the diagonals and two circles from their crossing, 5 in and 4-3/4 in across. Step off 24 points on the inner circle with the compass set about 5/8 in apart, adjusting until they come out even. Bore 1/8 in holes just inside the inner circle at the points, then saw out the 5 in circle (bore first, or the disk may split).

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet

Gerekli aletler:

PusulaPusula
Kurşun kalemKurşun kalem
El matkabıEl matkabı
Kıl TestereKıl Testere
4

Set the spokes and roll the edge

Push dry No. 4 reed spokes through the holes, about 5-1/2 in projecting below. Soak bottom and spokes about 15 minutes. Bend each spoke below the bottom down behind the two nearest spokes and out between the third and fourth; force the last two under the first two, making a pinwheel. Then bend them up across the edge of the wood, in front of three spokes and behind the fourth, inserting a short spoke about 4 in long in front of each first so the doubles cover the edge; press them flat and trim any that are too long.

Bu adım için malzemeler:

RattanRattan1 adet

Gerekli aletler:

20 Litrelik Kova20 Litrelik Kova
Deri bıçağıDeri bıçağı
Marangoz keskileriMarangoz keskileri
5

Triple-weave the side

Put in three soaked No. 3 reed weavers between spokes A-B, B-C and C-D. Each time take the weaver farthest behind in front of the two nearest spokes, behind the third and out in front of the next two. Use weavers no longer than 8 ft; when one runs out, press it back a little and push a new reed in about 1-1/2 in. Press every throw down, and weave to 3 in high.

Bu adım için malzemeler:

RattanRattan1 adet

Gerekli aletler:

20 Litrelik Kova20 Litrelik Kova
Deri bıçağıDeri bıçağı
6

Make the border

Break-down-tight border: bend spoke A behind B and out between B and C, B behind C, and so on to E; then lay the end of A over B to E, in front of F, behind G and out between G and H, and bring F down behind A's end; continue round, leaving the first ends loose so the last spokes can be worked under them. Or use the simple break-down: each spoke behind the next, in front of the one after, and behind the next, not out again.

Gerekli aletler:

Deri bıçağıDeri bıçağı
7

Finish

When dry, cut the long ends off close with a knife, without cutting a weaver. Singe off hairy fibres over a flame that will not smut. Do not leave reeds in water longer than needed, as they turn dark; dampen them often while weaving so they pack down closer. He also mentions bleaching with chloride of lime in water set in sunlight, but warns too much gives a whitish look; it is not part of this blueprint.

Gerekli aletler:

Deri bıçağıDeri bıçağı
Propan PürmüzPropan Pürmüz
8

Troubleshooting

Reed basket troubleshooting.

Flow

Loading...
9

History and honest limits

From "Reed Furniture: A Reed Basket" by Chas. M. Miller, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 257-260). Reed sizes are his trade numbers (No. 3, No. 4). Bleaching is described in his text but left out here. The tools and metric figures are ours.

Malzemeler

2
  • Yer Tutucu
  • 1 adet
    Yer Tutucu

Gerekli Aletler

8

Bu planla yapılan

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...