İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)
Woody

Oluşturan

Woody

13. Kasım 2026NO
12
0
0
0
0

Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)

A six-string guitar "having straight lines, giving it an old-fashioned appearance", from The Boy Mechanic (1913): a tapered box of hard maple with a seasoned soft-pine top, a drawknifed neck, frets cut from hatpins and a 24 in scale. Sizes are read on the 1913 scan. "If care is taken in selecting the material, and having it thoroughly seasoned, the finished instrument will have a fine tone."
İleri
About 1 week, with glue drying

Talimatlar

1

Cutting list and frets

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic

"The sides, ends and bottom are made of hard wood, preferably hard maple, and the top should be made of a thoroughly seasoned piece of soft pine." (J. H. Stoddard, Carbondale, Pa.)
3

Cut the pieces

Cut from thoroughly seasoned wood: top 3/16 by 14 by 17 in (soft pine); bottom 3/16 by 14 by 17 in, two sides 3/16 by 3-5/8 by 16-3/4 in, and ends 3/16 by 3-5/8 by 13-1/8 in and 9-5/8 in (hard maple); neck 1 by 2-5/16 by 18-1/2 in; fingerboard 3/16 by 2-5/8 by 16 in.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Çam tahtaÇam tahta1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Şerit MetreŞerit Metre
Marangoz gönyesiMarangoz gönyesi
4

Shape the neck and fingerboard

Taper the neck from G to F and from J to F, with the back rounded, using a drawknife: 2-3/8 in at the heel, 1-7/8 in at the nut F, and a head 2-3/4 in wide and 6-1/2 in long. Taper the fingerboard to match. Glue a piece of hard wood 1/4 in square and 1-7/8 in long across the neck at F as the nut. Glue the fingerboard to the neck and clamp it until the glue sets.

Bu adım için malzemeler:

Sert ağaç çıtasıSert ağaç çıtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

İki Saplı Yontma Bıçağıİki Saplı Yontma Bıçağı
El TesteresiEl Testeresi
Çubuklu işkenceÇubuklu işkence
5

Fret the fingerboard

Mark the frets from the nut using the computed positions in step 1 (fret 1 at 1.347 in, fret 12 at 12 in). His drawing gives only five spaces, 1-2/5, 1-3/16, 1-1/8, 1-1/16 and 1 in; added up they put the 5th fret about 0.3 in short of the true place, so they are shown for history only. Cut pieces from hatpins and fasten them across the fingerboard with small wire staples. Mark accurately: the frets decide the pitch.

Bu adım için malzemeler:

Şapka iğnesiŞapka iğnesi1 adet
Tel kroşeTel kroşe1 adet

Gerekli aletler:

Yassı Ağızlı PenseYassı Ağızlı Pense
ÇekiçÇekiç
Şerit MetreŞerit Metre
Marangoz gönyesiMarangoz gönyesi
6

Build the box

Glue the sides and ends together, so the body is 10 in wide at the neck end, 13-1/2 in at the tail and 16-1/2 in long. Glue the front on, put heavy weights on top and give the glue time to dry. Fasten pieces of soft wood in the corners as braces, glue a small block C inside the neck end to take the bolt, and glue strips of soft wood K across the front and back to strengthen them. Cut the sound hole in the top as drawn.

Bu adım için malzemeler:

Yumuşak ağaç çıtaYumuşak ağaç çıta1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Çubuklu işkenceÇubuklu işkence
Kol matkabı ve ucuKol matkabı ve ucu
7

Fit the neck

Make the brace D 1 in thick, to any shape you like. Glue the neck to the box and secure it with a carriage bolt at A through the end and block C. Glue the back on and smooth the outside with sandpaper.

Bu adım için malzemeler:

Sert ağaç çıtasıSert ağaç çıtası1 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Zımpara KağıdıZımpara Kağıdı1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
Çubuklu işkenceÇubuklu işkence
8

Make and place the bridge

Make the bridge 6 in long, 1 in wide and 3/8 in high, with an old hatpin or wire of the same size secured on top with pin staples as the saddle E. Drill six 3/16 in holes in it for the pins. Glue it on the top so the distance from the nut F to the saddle E is just 24 in.

Bu adım için malzemeler:

Sert ağaç çıtasıSert ağaç çıtası1 adet
Şapka iğnesiŞapka iğnesi1 adet
Tel kroşeTel kroşe1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
El TesteresiEl Testeresi
Şerit MetreŞerit Metre
9

String it

Fit the turning pegs B in the head and string the guitar, holding the strings in the bridge with the pins. He bought the pegs and strings from a music store.

Bu adım için malzemeler:

Akort BurgularıAkort Burguları1 adet
Gitar teliGitar teli1 adet
Köprü pimleriKöprü pimleri1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
10

Troubleshooting

Guitar troubleshooting.

Flow

Loading...
11

History and honest limits

From **The Boy Mechanic**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913, p. 320, "A Guitar That Is Easy to Make", sent in by J. H. Stoddard of Carbondale, Pa.; sizes read on the 1913 scan (archive.org boymechanicthing01unse). He dimensions only the first five fret spaces, and they disagree with equal temperament; the fret positions used are computed by us. The sound hole, saddle and string tensions are not dimensioned. The tools and metric figures are ours.

Malzemeler

12

Gerekli Aletler

8

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...