İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Clamping Caul: Zinc Plate with a Pine Backing Board (Adamson, 1889)
Woody

Oluşturan

Woody

9. Kasım 2026NO
7
0
0
0
0

Clamping Caul: Zinc Plate with a Pine Backing Board (Adamson, 1889)

A caul spreads clamping pressure evenly over glued work. D. Adamson (1889) prefers zinc for veneering cauls because it lasts longer than wood: a plate 1/8 to 1/4 in. thick (1/8 in. is enough), with a loose backing board of sound pine about 1 in. thick that keeps it flat and holds its heat. Only the zinc is warmed; the pine backing goes on cold. Source: D. Adamson, "Practical Veneering", Work, 5 October 1889, pp. 453-455.
Başlangıç
Unknown

Talimatlar

1

Read Adamson

"Perhaps as a general thing the zinc is usually preferred of from 1/8 in. to 1/4 in. in thickness, the former being quite sufficient for ordinary purposes. ... Even with a zinc caul a backing of wood is necessary to keep it flat down to the work, and to prevent the heat from dispersing too rapidly."
2

Cut the zinc

Cut a zinc plate 1/8 in. thick (1/8 to 1/4 in. is usual; too thin does not hold the heat, thicker is only waste), large enough to cover the surface to be pressed and lying flat. Length and width are set by the work (not given). How it is cut is not given (ours: tin snips).

Bu adım için malzemeler:

Çinko levhaÇinko levha1 1/8 in.

Gerekli aletler:

Sac makasıSac makası
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Make the backing board

Cut a backing board of good sound pine about 1 in. thick, the size of the zinc, and plane it flat so it keeps the zinc flat down to the work (ours: plane and straightedge).

Bu adım için malzemeler:

Çam tahtaÇam tahta1 about 1 in. thick

Gerekli aletler:

Marangoz testeresiMarangoz testeresi
El rendesiEl rendesi
Düzlük mastarıDüzlük mastarı
4

Use it

Warm the zinc only (not so hot that it cannot be comfortably handled), lay it over the veneer with a sheet of slightly greased paper between, put the cold pine board on top, and screw down the hand-screws evenly until the glue oozes out at the edges. Leave it until the zinc is cold, an hour or two.

Gerekli aletler:

İşkencelerİşkenceler

Malzemeler

2
  • 1 1/8 in.
    Yer Tutucu
  • 1 about 1 in. thick
    Yer Tutucu

Gerekli Aletler

6

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...