İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)
Forge

Oluşturan

Forge

4. Kasım 2026NO
10
0
0
2
0

Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)

A tinsmith's colander for straining: a tapered tinplate body and a hollowed bottom, both punched full of holes, standing on a wired hoop, with two bow handles. The body pattern is a ring segment: outer radius = top diameter, inner radius = bottom diameter, which gives sides at 60 degrees. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 50-51. Unknown: sizes, solder. Picture: Figs. 126-127 of the book.
Orta
Unknown

Talimatlar

1

Set out the body pattern

Choose the top and bottom diameters. On tinplate, strike an arc with radius equal to the top diameter and, from the same centre, one equal to the bottom diameter (Fig. 127); the sides then slope at 60 degrees. Mark the rows of holes, add edges for a grooved seam and the wire, and cut it out.

Bu adım için malzemeler:

Teneke sacTeneke sac1 body

Gerekli aletler:

PergelPergel
ÇizecekÇizecek
Sac makasıSac makası
2

Break, punch and planish the body

'Break' the pattern through the rollers, turning it the opposite way each pass, so it won't crease when bent. Punch the holes on a hardwood block, then flatten and planish the burrs.

Gerekli aletler:

Sac bükme silindirleriSac bükme silindirleri
Sac delme zımbasıSac delme zımbası
Sert Ahşap BlokSert Ahşap Blok
Perdah çekiciPerdah çekici
3

Seam and wire the body

Set off the edges for a grooved seam, bend the body to shape and seam it. Solder the seam inside. Set off an edge on the wide end and wire it with No. 10 B.W.G. wire. If you like, raise a swage about 1 1/2 in below the wired edge: it stiffens the colander and looks better.

Bu adım için malzemeler:

Demir telDemir tel1 No. 10 B.W.G.
Kalay-kurşun lehimKalay-kurşun lehim1 seam

Gerekli aletler:

Ahşap TokmakAhşap Tokmak
KazıkKazık
Elektrikli HavyaElektrikli Havya
DekapanDekapan
4

Make and fit the bottom

Cut out the bottom, hollow it and edge it to fit the small end. Inside, mark circles from 1 in across at the centre, each 1 in wider than the last, out to the edge. Punch holes at short intervals round them and flatten the burrs on an upturned hollowing hammer. Solder the bottom on.

Bu adım için malzemeler:

Teneke sacTeneke sac1 bottom
Kalay-kurşun lehimKalay-kurşun lehim1 bottom

Gerekli aletler:

PergelPergel
Sac makasıSac makası
Sac delme zımbasıSac delme zımbası
Perdah çekiciPerdah çekici
Elektrikli HavyaElektrikli Havya
DekapanDekapan
5

Add the hoop and handles

Cut a strip 1 1/2 in wide, as long as the circumference of the bottom. Wire it with No. 10 B.W.G., round it, seam it and solder it on as the foot. Rivet a pair of bow handles opposite each other at the top.

Bu adım için malzemeler:

Teneke sacTeneke sac1 hoop
Demir telDemir tel1 hoop
Kalay-kurşun lehimKalay-kurşun lehim1 hoop
SapSap2 bow handles
Demir perçinlerDemir perçinler1 number not given

Gerekli aletler:

Sac makasıSac makası
Elektrikli HavyaElektrikli Havya
DekapanDekapan
Perçin çekiciPerçin çekici
6

Clean and scald

Clean with turpentine and whiting, then polish with dry whiting. Before first use, steep it a short time in boiling water, as for any metal article for the kitchen.

Gerekli aletler:

TerebentinTerebentin
Kalsiyum karbonat (tebeşir tozu)Kalsiyum karbonat (tebeşir tozu)
SuSu

Malzemeler

5

Gerekli Aletler

15

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...