İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
N. B. Cooper of Gratis, Ohio, received US 26,020, dated 8 November 1859, for a churn-dasher. A frame slides into ways on the churn's ends and lifts out whole. Two bars run along its foot on pivots, one each side of the middle, each with blades and the lower half of a folding lever; the levers' upper halves meet at the dash rod. Working the rod up and down folds the levers and swings the bars and their agitators, driving the cream from side to side.
The patent gives no sizes; every size here is ours.
Orta
About 2 days
Talimatlar
1
1
The folding levers
The folding levers
Jupyter defteri yükleniyor…
2
2
Dashers that swing sideways, six weeks before
Dashers that swing sideways, six weeks before
Austin swung his side dashers from cranks. Cooper swings his agitators from the dash rod itself, by folding levers.
3
3
Read US 26,020
Read US 26,020
"It will be readily seen by reference to Fig. 2 that the operation of the levers and agitators is of such a character as to force the cream rapidly from one side of the churn to the other, and that such currents must be forcibly interrupted by the agitators upon either side"
4
4
Shell A and ways x
Shell A and ways x
From 20 mm hardwood make a box 400 x 320 mm and 420 mm deep inside. Glue two strips 15 x 15 mm up the inside of each end, 90 mm apart, as the ways x. Fill the box with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Sert Ağaç Tahtası3 adet
Ahşap Tutkalı1 adet
Ahşap vidalar24 adetGerekli aletler:
Daire testere tezgâhı
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Marangoz gönyesi
Şerit Metre
Su5
5
Frame B
Frame B
Cut two end posts 89 x 14 mm, 460 mm long, to slide between the ways, and a top bar 400 x 40 x 30 mm with a 31 mm square hole in its middle for the dash rod; screw the bar across the posts' tops. Screw a block 16 x 24 x 24 mm to each post's inside 25 mm each side of the middle and 110 mm up, and bore them 10.4 mm for the pivot rods b'.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Ahşap Tutkalı1 adet
Ahşap vidalar12 adetGerekli aletler:
Daire testere tezgâhı
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Marangoz gönyesi6
6
Bars b, blades c and folding levers d
Bars b, blades c and folding levers d
Bore two hardwood bars 20 mm square and 336 mm long through their length, 10.4 mm, and pin each on a 10 mm stainless rod 396 mm long that turns in the blocks. In the middle of each bar fix a lower arm, 110 mm between its pin holes, pointing up and out, and fix two blades 54 x 50 x 8 mm at right angles to it, pointing down and out, staggered so the two bars' blades pass each other. Join each arm's end to an upper lever, 180 mm between pins, and both upper levers to the foot of a dash rod 30 mm square and 550 mm long, with 10 mm stainless pins, washers and split pins. Glue two agitator bars f, 16 mm square and 340 mm long, across each upper lever.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Paslanmaz çelik çubuk2 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Düz Pul8 adet
Kopilya8 adetGerekli aletler:
Daire testere tezgâhı
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı
Zımpara Kağıdı
Şerit Metre7
7
The build in 3D
The build in 3D
FreeCAD model of this build, one side and one end left off: the shell with its ways, the frame with the pivot rods and the dash rod, the two bars with their arms and blades, the upper levers with the agitator bars. The bars were turned from 40 degrees up to 40 degrees down.
8
8
Churn
Churn
Pour about 25 litres of heavy cream at about 15 °C into the shell, checked with the thermometer. Slide the frame down the ways and work the dash rod up and down steadily, timing it. When the butter comes, lift the frame out whole, gather the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema25 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi9
9
Troubleshooting
Troubleshooting
Folding-lever churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**N. B. Cooper** of Gratis, Preble County, Ohio, US 26,020, 8 November 1859, "Churn-Dasher". He did not claim jointed levers or agitators on them, "as these devices are well known", but "the arrangement of the arms d, d, on the two pivots b', b', one on each side of the upright B, when the upright B is made removable, by means of the ways x, x". The patent gives no sizes; every size here is ours. His central upright is here the top bar's guide, and the rod is worked by hand rather than by gearing and a crank.
Malzemeler
10- 3 adetYer Tutucu
- 3 adetYer Tutucu
- 36 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 8 adetYer Tutucu
- 8 adetYer Tutucu
- 25 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
17- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
1Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out
Buttercup tarafından
Ağaç işleri
12
0
0
0
0
0

Oval-Breaker Rod Dasher: Breakers Strung on Two Rods, Add More for More Agitation
Buttercup tarafından
Ağaç işleri
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

