SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Cracked C4 Cut: Cracking-Still Gas Liquefied and Split in Four Columns at 200 psi (Eastman, Texas Co., US 2,014,724)
The gas from a cracking still is a mixture of light hydrocarbons. Compress it, chill it until it liquefies, and run it through four columns in turn: each column sends one group off its top, and the fourth gives the butanes and butylenes together, the C4 cut.
Result: a liquefied butane-butylene cut. Eastman does not give its composition.
Source: Eastman, US 2,014,724 (1935). Not given: the cut's make-up, how the impurities are removed, the refrigerant. The gas from Burton's still is used here as the same kind of cracking-still gas. Extremely flammable gases under pressure. Picture drawn by Youblob.
Uzman
1 day
Talimatlar
1
1
Clean the cracking-still gas
Clean the cracking-still gas
Take the gas from a cracking still, preferably after its gasoline has been separated and impurities such as hydrogen sulfide, carbon dioxide and water removed. Eastman does not say how they are removed.
Bu adım için malzemeler:
Kraking gazı1 as requiredGerekli aletler:
Basınçlı gaz tüpü2
2
Compress and chill it until it liquefies
Compress and chill it until it liquefies
Compress the gas, then cool it far enough that it liquefies almost completely.
Gerekli aletler:
Gaz kompresörü
Kriyojenik damıtma kolonu
Basınç Göstergesi3
3
Take off methane and hydrogen, then the C2s
Take off methane and hydrogen, then the C2s
Run the liquid through a series of fractionating columns at about 200 lbs per square inch. Methane and hydrogen escape from the top of the first column, at about -100 °F; ethylene and ethane from the second, at about -25 °F. Eastman burns the methane and hydrogen as fuel in his cracking furnaces.
Gerekli aletler:
Kriyojenik damıtma kolonuBasınç Göstergesi4
4
Take off propane and propylene
Take off propane and propylene
Propane and propylene leave the top of the third column, at about +100 °F.
Gerekli aletler:
Fraksiyonlu imbikBasınç Göstergesi5
5
Take the butanes and butylenes from the fourth column
Take the butanes and butylenes from the fourth column
The butane and butylene come off the top of the fourth column, at about +200 °F under the same pressure. This is the C4 cut. Ours: condense it into pressure cylinders.
Gerekli aletler:
Fraksiyonlu imbikBasınç GöstergesiBasınçlı gaz tüpüMalzemeler
1- 1 as requiredYer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.