İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)
Charlie

Oluşturan

Charlie

3. Kasım 2026DE
10
0
0
0
0

Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)

A complete fractional distillation set: a globular flask, Young and Thomas's 'evaporator' still-head built of stacked glass sections, a Liebig condenser and a row of receivers. In each section the rising vapour is forced through the liquid running back down, so the mixture separates better at each step. Result: a fractionating apparatus for separating liquids by boiling point, the fractions caught in receivers changed at set temperatures. Source: S. Young, Fractional Distillation (1903), pp. 4-7, 115-116, 166-168. Picture: Figs. 37 and 38 of the book.
İleri
Unknown

Talimatlar

1

Choose the still

Use a globular flask, since a flat-bottomed one may crack over a naked flame, no larger than the amount of liquid needs. Fit it with a cork for the still-head. Ours: a round-bottom flask.

Bu adım için malzemeler:

Yuvarlak dipli balonYuvarlak dipli balon1 still
Mantar tıpalarMantar tıpalar1 still cork

Gerekli aletler:

Bunsen bekiBunsen beki
2

Blow the evaporator still-head

Build the still-head of sections joined end to end. Each outer tube is 22 to 24 mm inside and about 10 to 10.5 cm long, constricted at the bottom. In it stands a thin inner tube, 7.5 to 8 mm inside and 60 mm long, open at both ends, with two large holes near its top. Its lower end widens into a funnel resting on the constriction, with three or four tiny glass beads fused to the rim so it does not fit too tightly. Over it stands an intermediate tube about 14 mm inside and 50 mm long, like a small inverted test tube. A small funnel, slightly wider than the dip in the outer tube above, sits on top of it on three glass legs. Small glass projections centre the tubes. Make the head long enough that the thermometer's bulb and stem both sit in the vapour, with a side delivery tube at the top.

Bu adım için malzemeler:

Cam tüpCam tüp1 sections, inner and intermediate tubes, delivery tube

Gerekli aletler:

Tezgâh üstü cam üfleme şalomasıTezgâh üstü cam üfleme şaloması
3

Fit the condenser

Use a Liebig condenser, about 7 or 8 mm inside for the inner tube and 15 mm for the outer, cooled by running water. Pass the delivery tube through a cork into it. Draw out the joint where the wide inlet meets the narrow tube so no pool of liquid lies there. Bend the narrow tube so the condenser can stand upright. Above about 170 °C use a long tube cooled by air instead of water.

Bu adım için malzemeler:

Su soğutmalı kondenserSu soğutmalı kondenser1 condenser
Mantar tıpalarMantar tıpalar1 condenser cork

Gerekli aletler:

Tezgâh üstü cam üfleme şalomasıTezgâh üstü cam üfleme şaloması
SuSu
4

Set the heat and the receivers

Heat with a Bunsen burner, its top about 2 mm below the flask so the small flame touches the glass, shielded from draughts. Add a few pieces of porous porcelain (a broken clay pipe will do) or pumice if the liquid bumps. Set a thermometer in the still-head and a row of small flasks as receivers.

Bu adım için malzemeler:

TermometreTermometre1 still-head thermometer
Toplama balonuToplama balonu10 receivers

Gerekli aletler:

Bunsen bekiBunsen beki
Bilinmeyen malzemeBilinmeyen malzeme
5

Distil in fractions

Read the barometer and correct the set temperatures for it. Distil steadily. In each section, condensed liquid seals the narrow passage, so the vapour rises up the inner tube, down between the tubes and up again, while liquid drips from section to section back to the still. Collect the distillate in fractions, changing the receiver each time the temperature reaches one of the values fixed beforehand.

Gerekli aletler:

Cıvalı barometreCıvalı barometre
Bunsen bekiBunsen beki
SuSu

Malzemeler

6

Gerekli Aletler

5

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...