İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

Oluşturan

Forge

14. Kasım 2026NO
10
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
İleri
A day at the forge

Talimatlar

1

His weights

Jupyter defteri yükleniyor…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

Bu adım için malzemeler:

Pota çeliğiPota çeliği1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
BalyozBalyoz
Demirci kerpeteniDemirci kerpeteni
Delik genişletme zımbasıDelik genişletme zımbası
Su verme kovasıSu verme kovası
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet
Kabarcıklı çelik çubuklarKabarcıklı çelik çubuklar1 adet
Boraks tozuBoraks tozu1 adet
KumKum1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
Sıcak keskiSıcak keski
ÖrsÖrs
BalyozBalyoz
Demirci kerpeteniDemirci kerpeteni
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Delik genişletme zımbasıDelik genişletme zımbası
Sıcak keskiSıcak keski
ÖrsÖrs
ÇekiçÇekiç
Demirci kerpeteniDemirci kerpeteni
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Delik genişletme zımbasıDelik genişletme zımbası
ÖrsÖrs
ÇekiçÇekiç
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

Gerekli aletler:

ÖrsÖrs
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

Bu adım için malzemeler:

Dişbudak kütüğüDişbudak kütüğü1 adet
Ahşap kamalarAhşap kamalar1 adet

Gerekli aletler:

İki Saplı Yontma Bıçağıİki Saplı Yontma Bıçağı
Marangoz keskileriMarangoz keskileri
ÇekiçÇekiç
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

Malzemeler

7

Gerekli Aletler

10

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...