İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
İleri
A day at the forge per pair
Talimatlar
1
1
Read Edwinson
Read Edwinson
"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2
2
Weld the blanks
Weld the blanks
As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.
Bu adım için malzemeler:
Dövme demir çubuk1 adet
Pota çeliği1 adet
Boraks tozu1 adetGerekli aletler:
Demirci ocağı
Örs
Balyoz
Sıcak keski
Demirci kerpeteni3
3
Bottom swage
Bottom swage
Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).
Gerekli aletler:
Demirci ocağı
Örs
Çekiç
Demirci kerpeteni4
4
Top swage
Top swage
Forge the matching top tool with a neck for its handle.
Gerekli aletler:
Demirci ocağı
Örs
Çekiç
Demirci kerpeteni5
5
Cut the grooves
Cut the grooves
Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.
Gerekli aletler:
Demirci ocağı
Fuller (oluk açma demiri)
Örs
Eğeler (El Eğesi)6
6
Handle or spring
Handle or spring
Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).
Bu adım için malzemeler:
Fındık çubukları (yeşil, esnek)1 adet
Yumuşak çelik yuvarlak çubuk1 adet
Demir tel1 adet
Yay çeliği şeridi1 adetGerekli aletler:
Demirci ocağı
Örs
Çekiç7
7
Grind and harden
Grind and harden
Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).
Gerekli aletler:
Bileme taşı çarkı
Demirci ocağı
Su verme kovası8
8
Use them
Use them
Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.
Gerekli aletler:
Demirci ocağı
Balyoz
Kumpas9
9
Troubleshooting
Troubleshooting
Swage troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.
Malzemeler
7- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
11- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.




