İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
Ed

Oluşturan

Ed

9. Kasım 2026FI
10
0
0
0
0

Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)

An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils. In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it. Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
İleri
Unknown

Talimatlar

1

Read Taylor

"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2

Fit the immersion heater

Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.

Bu adım için malzemeler:

Bilinmeyen metalBilinmeyen metal1 kettle body
Isıtma elemanıIsıtma elemanı1 immersion heater

Gerekli aletler:

Sert lehim şalomasıSert lehim şaloması
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Build the switch-on-dry unit

On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.

Bu adım için malzemeler:

Bilinmeyen yalıtım malzemesiBilinmeyen yalıtım malzemesi1 switch unit body
Bilinmeyen metalBilinmeyen metal1 pins, contacts and strip
Bimetal şeritBimetal şerit1 dry-switch disc

Gerekli aletler:

Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
4

Make the steam unit

Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.

Bu adım için malzemeler:

Bimetal şeritBimetal şerit1 steam disc
Bilinmeyen yalıtım malzemesiBilinmeyen yalıtım malzemesi1 steam unit body and lever
YayYay2 C-springs
O-ring contaO-ring conta1 adet

Gerekli aletler:

Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
5

Close up and use

Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.

Bu adım için malzemeler:

Bilinmeyen yalıtım malzemesiBilinmeyen yalıtım malzemesi1 outer housing
Fişli esnek kabloFişli esnek kablo1 kettle lead with socket

Malzemeler

7

Gerekli Aletler

5

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...