İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Electric Soldering Iron: Miner, 1890
English
Ed

Oluşturan

Ed

12. Ekim 2026FI
24
0
0
0
0

Electric Soldering Iron: Miner, 1890

Earlier electric soldering irons heated a hollow copper head from inside, through finely divided carbon pressed against the tip, so the whole outside of the head lost heat to the air. Willard M. Miner of Plainfield, New Jersey, patented the alternative in 1890, US 421,185: keep the copper head solid, which holds its heat longer, and wind the heating resistance round the outside of it, under a shell that concentrates the heat on the copper and stops it escaping. The coil is German silver wire, wound round a reduced part of the head without touching it, with one end connected to the head and the other to the supply.
Orta
Workshop process

Talimatlar

1

Turn the head

Turn a solid copper head with its point. A little back from the point, cut the head down to a smaller diameter for some distance, leaving a shoulder, and thread a shank at its rear end.

Bu adım için malzemeler:

Bakır yuvarlak çubukBakır yuvarlak çubuk1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
2

Wind the coil

Coil German silver wire round the reduced part of the head, the coil slightly larger than the head so the two do not touch. Connect one end of the coil to the head at the shoulder; the other end goes to the supply.

Bu adım için malzemeler:

Alman gümüşü direnç teliAlman gümüşü direnç teli1 as required

Gerekli aletler:

Kombine PenseKombine Pense
3

Shell

Slip on the shell, of brass lined with non-conducting material. Close its inner end with an insulating disc held by a washer and nut on the threaded shank.

Bu adım için malzemeler:

Astarlı pirinç kılıfAstarlı pirinç kılıf1 adet
Yalıtkan uç diskiYalıtkan uç diski1 adet

Gerekli aletler:

Kurbağacık anahtarKurbağacık anahtar
4

Handle

Screw the shank into the metal socket in the handle, which takes the second connection.

Bu adım için malzemeler:

Sap İçin Sert Ağaç KütüğüSap İçin Sert Ağaç Kütüğü1 adet

Malzemeler

5

Gerekli Aletler

3

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...