SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Oluşturan

Penny

14. Ekim 2026DK
25
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Orta
Two to three days

Talimatlar

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Bu adım için malzemeler:

Lama takım çeliği çubukLama takım çeliği çubuk1 adet

Gerekli aletler:

Metal EğeMetal Eğe
El matkabıEl matkabı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Demirci ocağıDemirci ocağı
Su verme kovasıSu verme kovası
Koruyucu gözlükKoruyucu gözlük
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Bu adım için malzemeler:

Sert ağaç çıtasıSert ağaç çıtası2 adet
Yumuşak Çelik ÇubukYumuşak Çelik Çubuk0.3 m

Gerekli aletler:

Metal EğeMetal Eğe
Demirci ocağıDemirci ocağı
Su verme kovasıSu verme kovası
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Bu adım için malzemeler:

Pirinç LevhaPirinç Levha1 adet
Mumlu keten iplikMumlu keten iplik3 m

Gerekli aletler:

Sac makasıSac makası
El matkabıEl matkabı
Metal EğeMetal Eğe
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Gerekli aletler:

Metal EğeMetal Eğe
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Bu adım için malzemeler:

Pirinç külçePirinç külçe2 kg
Odun KömürüOdun Kömürü1 as required
Döküm kumuDöküm kumu5 kg

Gerekli aletler:

Demirci ocağıDemirci ocağı
Ateş Kili PotasıAteş Kili Potası
Pota MaşasıPota Maşası
Derece (üst ve alt kalıp kasası)Derece (üst ve alt kalıp kasası)
Kaynak eldivenleriKaynak eldivenleri
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Bu adım için malzemeler:

SuSu1 litre

Gerekli aletler:

Dereceli silindirDereceli silindir
Metal EğeMetal Eğe
7

A binary set of weights

Jupyter defteri yükleniyor…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Malzemeler

9

Gerekli Aletler

12

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...