İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Fermenter Lid with Airlock Seat, 3D Printed in PETG
A snap-on lid that turns a small food-grade pail into a fermenter. It follows L. P. Beadle's 1980 US patent 4,218,964: an off-centre tapered hole that matches the airlock stem's taper, a triangular rim set in a groove so it flexes round the stem, stiffening rings, and a snap-fit edge. You measure your pail's rim and make the file for it. All sizes are ours, and we have not printed or tested it yet.
Başlangıç
About 10 hours, mostly printing
Talimatlar
1
1
Lid size, stem depth and gas force
Lid size, stem depth and gas force
Jupyter defteri yükleniyor…
2
2
Read US 4,218,964
Read US 4,218,964
"The stem support structure 30 includes a tapered hole the depth and slope of which are adapted to conform to the taper of stem 26 and to provide a resilient, gripping action ... annular rim portion 35 is defined by depressed circular groove 36 which provides the annular rim 35 with a type of hinge action." He put the hole off centre so the lid would not crack. The picture is our section.

3
3
Measure the pail
Measure the pail
Use a food-grade plastic pail with a rim lip all round. Measure the lip's outside diameter, and from the pail's top edge to the underside of the lip.
Gerekli aletler:
Dijital Kumpas 6 İnç
Fermantasyon kovası4
4
Make the lid for your pail
Make the lid for your pail
Run it in FreeCAD with your two measurements: OUT=. LIP_D= LIP_H= freecadcmd build_all.py
build_all.pypython
Gerekli aletler:
Masaüstü Bilgisayar
CAD yazılımı5
5
Print the lid
Print the lid
Print it top face down on the bed, no supports: the skirt and stiffening rings grow upwards. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls. The file here is for a 180 mm lip.
Bu adım için malzemeler:
PETG filament125 gGerekli aletler:
FDM 3B yazıcı
3B yazıcı nozul seti6
6
Fit the airlock
Fit the airlock
Push the airlock's stem down into the hole by hand until it wedges, about 30 mm for our airlock. Do not force it further.
Gerekli aletler:
Fermantasyon kilidi7
7
Leak test
Leak test
Fill the airlock to its line with water. Snap the lid on the empty pail. Press the middle of the lid gently: gas must bubble through the airlock, with no hiss at the rim or stem.
Gerekli aletler:
Fermantasyon kovası
Fermantasyon kilidi
Su8
8
Sanitise
Sanitise
Wipe or soak the lid in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.
Gerekli aletler:
Dezenfektan
Su9
9
Close the fermenter
Close the fermenter
Start the bead under the lip at one side and press the lid down all round until it snaps on.
Gerekli aletler:
Fermantasyon kovası10
10
Troubleshooting
Troubleshooting
Lid problems and fixes.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Leigh P. Beadle**, US 4,218,964, filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His lids were moulded in flexible plastic, and he noted that drilling a plain hole in the middle of a lid led to cracks and to gas escaping round the stem. He gives no sizes. Ours: every size, PETG, the bead and the fit to a measured pail. One change: his rim rises above the lid's top; ours stands in a recess with its top level with the lid, so the lid prints flat. PETG is stiffer than his plastic, so the grip comes more from the matched taper than from the rim. Checked in CAD; not yet printed or brewed with by us.
Malzemeler
1- 125 gYer Tutucu
Gerekli Aletler
9- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
1Bağlı Plan Malzemeleri
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.




