İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked
Martin

Oluşturan

Martin

9. Kasım 2026NO
10
0
0
0
0

Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked

Joseph Forsyth of Wheeling, Virginia, received US 22,022, dated 9 November 1858, for working a churn by power from a big belt wheel. The pulley head slides along a guide block to tighten or slack the belt, which starts or stops the churn. The churn stands on a carriage fixed to the head, so its shaft stays in line with the pulley's. A platform on four screws raises or lowers different churns to the pulley's height. This rung builds it full size with a hand-cranked wheel and a rope belt.
Orta
About 2 days

Talimatlar

1

Speed, rope and slack

Jupyter defteri yükleniyor…
2

Churns worked by power, before it

Brush worked a dasher from a dog's tread-wheel. Forsyth turns a crank churn by a belt and stops it by slacking the belt.
3

Read US 22,022

"The nature of my invention consists, first, in combining the carriage D with the movable pulley head H H in such a manner that the said carriage will move with the head when it is required to stop or start the motion of the churn, thereby enabling me to keep the shafts of the pulley, and churn in line."
4

Wheel A and posts B

Cut a plywood disc 1160 mm across and two discs 1200 mm across from 18 mm plywood. Glue and screw a larger disc to each face of the smaller one: the gap between them is the rope groove C. Screw a 160 mm hub block on each side. Stand two 70 mm posts 730 mm tall on 900 mm sills, 150 mm apart, each with two braces. Bolt a flange bearing on each post's outer face, 700 mm up, and run a 30 mm shaft M through bearings, posts and wheel, cross-bolted to the hub.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha3 adet
Ahşap TutkalıAhşap Tutkalı1 adet
#8 x 1" ahşap vidası#8 x 1" ahşap vidası60 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm4 adet
#10 x 3" ahşap vidası#10 x 3" ahşap vidası24 adet
Flanşlı rulmanFlanşlı rulman2 adet
Çelik mil 30 mmÇelik mil 30 mm1 adet
Altı köşe cıvata takımı M10Altı köşe cıvata takımı M105 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
İşkencelerİşkenceler
Kurbağacık anahtarKurbağacık anahtar
Su TerazisiSu Terazisi
Şerit MetreŞerit Metre
5

Crank

How the wheel is turned is not given; ours has a crank. Bolt a hardwood arm 350 x 70 x 30 mm on shaft M outside one bearing and glue a 30 mm dowel 150 mm long into it 280 mm from the shaft as the handle.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Altı köşe cıvata takımı M10Altı köşe cıvata takımı M101 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Zımpara KağıdıZımpara Kağıdı
Kurbağacık anahtarKurbağacık anahtar
6

Guide block and pulley head

Screw a 900 mm guide block U of 70 mm timber to the floor in line with the wheel, 1300 mm from shaft M. Lay a 400 mm head block on it. Cut two frames H from 50 x 8 mm flat bar, 420 mm long, and bolt them to the head block's sides so their ends run down the guide block's sides. Bolt a flange bearing on each frame's outer face 400 mm up. Make the pulley O like the wheel: a 200 mm disc between two 240 mm rings. Fit it on a 30 mm shaft through the bearings.

Bu adım için malzemeler:

Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm2 adet
#10 x 3" ahşap vidası#10 x 3" ahşap vidası8 adet
Yumuşak Çelik LamaYumuşak Çelik Lama2 adet
Altı köşe cıvata takımı M10Altı köşe cıvata takımı M104 adet
Flanşlı rulmanFlanşlı rulman2 adet
Çelik mil 30 mmÇelik mil 30 mm1 adet
Kontrplak levhaKontrplak levha1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
#8 x 1" ahşap vidası#8 x 1" ahşap vidası12 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Tezgah MengenesiTezgah Mengenesi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Dekupaj TestereDekupaj Testere
Kurbağacık anahtarKurbağacık anahtar
7

Strap F and thumb screw E

Bend a 30 x 5 mm flat bar into a bridge over the head block, 80 mm from the frames, and screw its legs to the guide block's sides. Drill its top for an M8 rod, run a nut onto the rod under the strap, and lock a wing nut on top as the thumb screw. Turn it down to clamp the head block.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
#8 x 1" ahşap vidası#8 x 1" ahşap vidası4 adet
Dişli milDişli mil1 adet
Altıgen SomunAltıgen Somun2 adet
Kanatlı somunKanatlı somun1 adet

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Demir TesteresiDemir Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
8

Carriage D and platform K

Bolt two 70 mm side bars, 865 mm long, to the head block's side, 330 mm apart, and join their far ends with a cross tie with a caster under its middle as the roller. Drill each bar twice for M12 rods (screws I), 360 mm apart; fix each rod with a nut above and below the bar. Run a nut down each rod, lay an 18 mm plywood platform 430 x 440 mm on them, and lock it with a second nut on top.

Bu adım için malzemeler:

Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm2 adet
Altı köşe cıvata takımı M10Altı köşe cıvata takımı M104 adet
Tekerlek seti (döner)Tekerlek seti (döner)1 adet
Dişli milDişli mil4 adet
Altıgen SomunAltıgen Somun16 adet
Düz PulDüz Pul8 adet
Kontrplak levhaKontrplak levha1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
Su TerazisiSu Terazisi
9

Arm X and the rope belt

Bolt a 140 mm flat-bar arm X with a 20 mm slot to a collar on the pulley shaft's end. Stand a crank churn on the platform and raise or lower the platform's nuts until its crank shaft is level with the pulley shaft and its handle V sits in the slot. Splice 12 mm cotton rope into a loop about 5 m long round both grooves (see the notebook), with the head slid towards the wheel.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Altı köşe cıvata takımı M10Altı köşe cıvata takımı M101 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu1 adet
Pamuk halatPamuk halat6 m

Gerekli aletler:

Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
Şerit MetreŞerit Metre
10

The build in 3D

FreeCAD model of this build: the wheel on its posts with the crank, the guide block, pulley head, strap and thumb screw, the carriage with its caster, platform K on its four screws, a stand-in churn and arm X. The rope is not drawn.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Pour about 10 litres of heavy cream at about 15 °C into the churn. Slide the head away from the wheel until the rope is tight and clamp it with the thumb screw. Turn the wheel steadily, about 10 times a minute, and time it. To stop, loosen the thumb screw and slide the head towards the wheel: the carriage and churn move with it. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

YayıkYayık
Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Churn drive troubleshooting.

Flow

Loading...
13

History and honest limits

**Joseph Forsyth** of Wheeling, Ohio County, Virginia (now West Virginia), US 22,022, 9 November 1858, "Operating Churns". He claimed the carriage D combined with the movable platform K. He gave no sizes, named only the "metallic" frames H, and did not say what turns wheel A or what the belt is: our hand crank, plywood wheel and pulley, cotton rope, timber, bearings, rods and caster are ours.

Malzemeler

21

Gerekli Aletler

18

Tasarım dosyaları

1

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...