İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

Oluşturan

Forge

13. Kasım 2026NO
10
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
Orta
About 5 hours

Talimatlar

1

How many balls

Jupyter defteri yükleniyor…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

Bu adım için malzemeler:

Çelik boru (kalın cidarlı, dişli uçlu)Çelik boru (kalın cidarlı, dişli uçlu)1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

Bu adım için malzemeler:

Pirinç Yuvarlak ÇubukPirinç Yuvarlak Çubuk1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Punta matkabı setiPunta matkabı seti
Matkap Ucu TakımıMatkap Ucu Takımı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

Gerekli aletler:

Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Tezgah MengenesiTezgah Mengenesi
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

Bu adım için malzemeler:

Bakır boruBakır boru1 adet
Kalay-kurşun lehimKalay-kurşun lehim1 adet
DekapanDekapan1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Matkap Ucu TakımıMatkap Ucu Takımı
Sütunlu MatkapSütunlu Matkap
Elektrikli HavyaElektrikli Havya
Tezgah MengenesiTezgah Mengenesi
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

Bu adım için malzemeler:

Çelik bilyeli rulmanlarÇelik bilyeli rulmanlar1 adet
Makine vidalarıMakine vidaları1 adet

Gerekli aletler:

Kurbağacık anahtarKurbağacık anahtar
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

Bu adım için malzemeler:

Sert Ahşap BlokSert Ahşap Blok1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Hortum kapliniHortum kaplini1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

Malzemeler

11

Gerekli Aletler

13

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...