İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)
Forge

Oluşturan

Forge

14. Kasım 2026NO
9
0
0
0
0

Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)

The simplest home-made taper reamer, from Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1905): tool steel turned to the taper wanted (his was 1/8 in. per foot), one side filed away exactly to the centre line so that two cutting edges remain, then hardened and ground on the flat face only. It reams a very smooth conical hole.
Orta
Two to three hours

Talimatlar

1

His taper

Jupyter defteri yükleniyor…
2

Read Griswold

"Turn a piece of tool steel to the proper taper and then file away one side until the flat surface coincides with the center line."
3

Turn the taper

Turn a piece of tool steel in the lathe to the taper of the part the hole must fit (his: 1/8 in. per foot). Length and diameter are ours: a little longer than the hole and spanning its two diameters.

Bu adım için malzemeler:

Takım çeliği çubukTakım çeliği çubuk1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
KumpasKumpas
4

File to the centre line

Hold it in the vice and file away one side until the flat face lies exactly on the centre line. This leaves a cutting edge on each side.

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Eğeler (El Eğesi)Eğeler (El Eğesi)
KumpasKumpas
5

Harden and grind

Harden it (ours: heat to a cherry red and quench in water, temper to a straw colour), then grind on the flat side only, never on the round.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Su verme kovasıSu verme kovası
Taşlama motoruTaşlama motoru
6

Troubleshooting

Reamer troubleshooting.

Flow

Loading...
7

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" VII, **Amateur Work** (Boston), vol. IV (1904-05), p. 128 (checked on the archive.org scan amateurwork04bostrich). He gives no size or temper for the reamer; those and the tools are ours. He finishes the hardened bushings with a copper lap and emery.

Malzemeler

1

Gerekli Aletler

7

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...