İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight.
Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them.
Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
Orta
Unknown
Talimatlar
1
1
Make the board and blocks
Make the board and blocks
Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.
Bu adım için malzemeler:
Sert ağaç kalası1 adet
Sert Ahşap Blok2 adet
Ahşap vidalar1 adetGerekli aletler:
Sırtlı testere
Düz tornavida2
2
Drill the face plates
Drill the face plates
Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.
Bu adım için malzemeler:
Pirinç Levha2 face platesGerekli aletler:
Pergel
Sac makası
El matkabı3
3
Make the teeth
Make the teeth
Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.
Bu adım için malzemeler:
Demir tel1 teethGerekli aletler:
Sac makası
Metal Eğe4
4
Set the teeth
Set the teeth
Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.
Gerekli aletler:
ÇekiçMalzemeler
5- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 2 face platesYer Tutucu
- 1 teethYer Tutucu
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

