SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Hand Lens 10×: a Small, Steep Lens Ground and Mounted
Penny

Oluşturan

Penny

14. Ekim 2026DK
25
0
0
0
0

Hand Lens 10×: a Small, Steep Lens Ground and Mounted

A 10× hand lens is a small convex lens of about 25 mm focal length: held close to the eye, its magnifying power is about a quarter of a metre divided by the focal length. Grind a small pair of discs to a steep curve as for any convex lens, then seat the convex one in a turned wooden ring with a cord to carry it. The picture: a low-power reading magnifier on a dictionary page; a 10× hand lens works the same way with a much smaller, steeper lens.
İleri
A week

Talimatlar

1

Two small discs

Cut two small glass discs, about 15 mm across, from glass at least 5 mm thick (each face of the lens goes over a millimetre deep), and pitch each to a short wooden handle.

Bu adım için malzemeler:

Cam levhaCam levha1 adet
Çam Ziftli TutkalÇam Ziftli Tutkal10 g
Sert ağaç çıtasıSert ağaç çıtası1 adet

Gerekli aletler:

Cam kesiciCam kesici
Cam kemirme pensesiCam kemirme pensesi
Koruyucu gözlükKoruyucu gözlük
2

Grind to a steep curve

Grind them together with wet coarse grit, the same disc always on top, until the faces are steep enough (see the notebook). Then the second faces. The bottom disc is the lens.

Bu adım için malzemeler:

SuSu1 litre

Gerekli aletler:

Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Silisyum karbür tanesiSilisyum karbür tanesi
3

Fine grind and polish

Fine grits, then polish both faces on a small pitch lap with tin oxide and water until clear.

Bu adım için malzemeler:

Kalay oksit (stannik oksit)Kalay oksit (stannik oksit)10 g
Çam Ziftli TutkalÇam Ziftli Tutkal30 g

Gerekli aletler:

Silisyum karbür tanesiSilisyum karbür tanesi
4

Check 10×

Focus the sun through it onto paper: the spot should be smallest about 25 mm from the lens. Grind deeper if it is longer.

Gerekli aletler:

CetvelCetvel
5

Turn the mount

Turn a hardwood ring on the lathe with a seat a snug fit for the lens and a small lip. Press the lens in, warm a little pitch round the back edge to hold it, drill a hole in the rim for a cord loop.

Bu adım için malzemeler:

Sert ağaç çıtasıSert ağaç çıtası1 adet
Çam Ziftli TutkalÇam Ziftli Tutkal2 g
Mumlu keten iplikMumlu keten iplik0.5 m

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
Oluklu Kalem (Guj)Oluklu Kalem (Guj)
Kesme kalemiKesme kalemi
Zımpara KağıdıZımpara Kağıdı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
6

Curve for 10×

Jupyter defteri yükleniyor…
7

Use

Hold the lens close to your eye and bring the object up until it is sharp.

Malzemeler

6

Gerekli Aletler

10

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...