İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)
Tex

Oluşturan

Tex

14. Kasım 2026FO
10
0
0
0
0

Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)

How a harness maker cuts and finishes straps, from P. N. Hasluck's Harness Making (1904): marked along the hide with an 8 ft straightedge or a compass, cut with the round knife on a cutting-board (or with a plough gauge, 1/2 to 5-1/2 in), always along the hide, then the edges knocked, trimmed with the spokeshave, scraped, sanded and polished with gum and a smooth bone.
Başlangıç
About 1 hour

Talimatlar

1

Widths

Jupyter defteri yükleniyor…
2

Read Harness Making

"Straps are always cut along the hide and not across it, the hide being much stronger lengthways."
3

Lay out

Lay the side on the bench with the back toward you. Mark straight lines with a blunt-pointed awl or seat-awl against a straightedge at least 8 ft long, without cutting the grain. Do not cut lower into the hide than the strap's width; cut shaped pieces from patterns.

Bu adım için malzemeler:

Koşum derisiKoşum derisi1 adet

Gerekli aletler:

Düzlük mastarıDüzlük mastarı
Saraç dolgu biziSaraç dolgu bizi
4

Cut

With the round knife: set the compass to the width, run one point along the edge and draw it toward you to leave a line, then cut from the right-hand end on a cutting-board, holding the leather steady with the left hand. With the plough: set the knife on the gauge (1/2 to 5-1/2 in) with the thumb-screw, hold the leather flat and press it forward with the guard tight to the edge. Cut reins first, then traces, back-bands and the rest; linings from the belly.

Gerekli aletler:

Saraç oluk pergeliSaraç oluk pergeli
Deri bıçağıDeri bıçağı
Kesme TahtasıKesme Tahtası
5

Finish the edges

Knock the edges along to consolidate them, trim them round and level with the spokeshave, run a glass scraper over them and sandpaper. For brown work, wipe with a thin solution of gum and water and rub with brown paper and a smooth bone to a polish. For black, dye, rub dry with a rag, and polish with brown paper and bone.

Bu adım için malzemeler:

Arap ZamkıArap Zamkı1 adet
Kahverengi ambalaj kâğıdıKahverengi ambalaj kâğıdı1 adet
Zımpara KağıdıZımpara Kağıdı1 adet

Gerekli aletler:

Çift saplı rendeÇift saplı rende
Cam kırığıCam kırığı
Kemik katlayıcıKemik katlayıcı
ÇekiçÇekiç
6

Troubleshooting

Strap troubleshooting.

Flow

Loading...
7

History and honest limits

From Paul N. Hasluck, **Harness Making** (1904) (checked on the archive.org scan harnessmaking00hasl, pp. 12, 42-44). Using broken glass (cullet) as the glass scraper, the tools and the metric figures are ours.

Malzemeler

4

Gerekli Aletler

9

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...