İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)
A saddle crupper runs from the back of a riding saddle to a padded loop (the dock) under the horse's tail, so the saddle cannot slide forward. This is the full-sized saddle crupper from Paul N. Hasluck's Saddlery (1904): a slit leather body, a buckled billet, and a dock shaped over string and wet brown paper. Every size is his.
Orta
About 1 day
Talimatlar
1
1
His sizes in centimetres
His sizes in centimetres
Jupyter defteri yükleniyor…
2
2
Read Saddlery, ch. V
Read Saddlery, ch. V
"Full-sized saddle cruppers (Fig. 9), which are used to prevent the saddle from advancing too much, are made about 1 in. wide, and sometimes a little more."
3
3
Cut the body
Cut the body
Cut the body about 1 in wide (or a little more) and about 1 ft 6 in long. Slit one end for about 5 in and turn the other end in for a 7/8 in buckle. Shave the points of the slits and the end of the chape.
Bu adım için malzemeler:
Koşum derisi1 adetGerekli aletler:
Deri bıçağı
Şerit Metre4
4
Make the billet and set the buckle
Make the billet and set the buckle
Cut a billet as wide as the buckle and 2 ft 4 in long; trim one end for the buckle and shave the other. Edge both pieces, polish the edges and crease them with a hot checker. Put on the buckle and stitch the billet: the first stitch by the buckle goes over the edge and through chape and billet together, the next through the loop. Run four or five stitches towards the point on each side, and come back to the buckle on the other side, making the last stitch over the side the same as the opposite side.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli demir toka1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Kenar pahlama aleti
Deri kenar perdahlayıcı
Kıvırma aleti
Propan Pürmüz
Biz
İki saraç iğnesi
Saraç mengenesi5
5
Put on the loop
Put on the loop
Put a loop on the flat lower down the body, about 6 in from the buckle, stitching it across at each end.
Bu adım için malzemeler:
Koşum derisi1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Köprü kalıp çubuğu
Biz
İki saraç iğnesi6
6
Shape the dock core
Shape the dock core
The dock is much smaller round than a gig crupper dock. Take a piece of string about 1 ft long and roll wet brown paper round it until it is the thickness you need in the middle; thin the ends by cutting the paper before damping it.
Bu adım için malzemeler:
İp1 adet
Kahverengi ambalaj kâğıdı1 adetGerekli aletler:
Makas
Sünger
Şerit Metre7
7
Cover the dock
Cover the dock
Cut the dock leather about 1 ft 1 in long; it must be soft and pliable, so damp it before stitching. Stitch it over the core as it is, without cutting a groove, drawing it very tightly over the paper. Dry the dock and finish it in shape.
Bu adım için malzemeler:
Koşum derisi1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Sünger
Biz
İki saraç iğnesi
Saraç mengenesi8
8
Join the dock and punch the billet
Join the dock and punch the billet
Stitch the dock to the slits with a splice of about 1-1/4 in. Put about a dozen holes in the billet, and vary the lengths to suit the size of horse.
Bu adım için malzemeler:
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Biz
İki saraç iğnesi
Deri delme zımbası9
9
Troubleshooting
Troubleshooting
Saddle crupper troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", saddle cruppers, pp. 40-41, Fig. 9; every fraction was read on the scan. He does not say how the billet fastens to the saddle; check against Fig. 9 and your saddle. The thread, tools and metric figures are ours.
Malzemeler
6- 4 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
- 4 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
Gerekli Aletler
13- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Riding Saddle: Web, Stuffed Seat, Hogskin Skirts, Knee-Pad Flaps and Quilted Panel on a Bought Tree (Hasluck, Saddlery, 1904)
Tex tarafından
Tekstil ve Deri
4
0
0
0
0
0

Saddle Breastplate: Rounded Side Straps, Neck Strap and Girth Strap on Covered Rings (Hasluck, Saddlery, 1904)
Tex tarafından
Tekstil ve Deri
6
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
