İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
Forge

Oluşturan

Forge

13. Kasım 2026NO
9
0
0
0
0

Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)

Fay M. Henkel of New Rochelle, New York, received US 1,695,188, dated 11 December 1928, for a cheap, compact bench saw in two parts. The stand has a platform that tilts on hinge pins for angled cuts, with a sliding angle follower and a rip guide. The power unit drops into it on trunnions, and a wing nut on a hanging screw raises or lowers the saw. The motor sits on two spring bars that soak up its vibration and keep the belt tight. Lifted out, the power unit stands on the bars' cap nuts and runs an emery wheel. The patent gives no sizes; every size here is ours, and our stand is wood and steel where his is cast.
İleri
About 4 days

Talimatlar

1

Raising the saw and tilting the platform

Jupyter defteri yükleniyor…
2

Read US 1,695,188

"It will thus be seen that the power unit has a three-point bearing which maintains it against accidental displacement, or, in other words, prevents it from getting out of proper alinement."
3

The stand: frame 1 and legs 3

Make a rectangular frame 460 x 360 mm of 25 x 90 mm hardwood, glued and screwed at the corners. Bolt a 250 mm pine leg 45 x 45 mm in each corner through a short length of steel angle screwed to frame and leg, as his corner plates 4 and lugs 5. Cut a notch 30 in the top of each long side, 60 mm from one end, 21 mm wide and 25 deep, for the trunnions. Screw a steel arm 34 across the other end with a 10.5 mm hole, and a lug 50 with an M10 tapped hole on the side away from the hinges.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Çam keresteÇam kereste1 adet
Yumuşak çelik köşebentYumuşak çelik köşebent1 adet
Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı8 adet
Ahşap vidalarAhşap vidalar24 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Çubuklu işkenceÇubuklu işkence
Kombine GönyeKombine Gönye
Şerit MetreŞerit Metre
Demir TesteresiDemir Testeresi
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Kılavuz koluKılavuz kolu
4

The platform 2

Cut 18 mm plywood 500 x 400 mm and glue a hardwood strip round its underside edges as the flange 8. Cut the opening 13 for the saw, 230 x 30 mm, and a hardwood block 15 to fill it. Rout a square groove 16 the length of the platform for the follower's bar. Screw two steel lugs 9 under one long edge, drilled to line up with holes 10 in the frame, and hinge it with steel pins held by split pins. Run an M10 tilt screw 49 up through lug 50, with a wing nut on its lower end as a handle, its top bearing under the platform.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk1 adet
KopilyaKopilya2 adet
Dişli milDişli mil1 adet
Kanatlı somunKanatlı somun1 adet
Ahşap vidalarAhşap vidalar16 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Freze motoruFreze motoru
Freze ucu takımıFreze ucu takımı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Çubuklu işkenceÇubuklu işkence
5

The power unit's frame, arbor and trunnions

Bolt two 40 x 6 mm steel flat bars 340 mm long into a frame 24 with spacers. Across one end fix a 20 mm round bar 28 whose ends stand out 25 mm each side as the trunnions 29. At the other end bolt two 30 mm flange bearings for the arbor 26, turned from 30 mm bar like the twin-saw table's, with a collar, a loose flange and an M20 thread for the blade's nut. Bolt a forked steel lug 31 on that end, its slot straddling the hanging screw.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk2 adet
Flanşlı rulmanFlanşlı rulman2 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı10 adet
Altıgen SomunAltıgen Somun3 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Eğe TakımıEğe Takımı
Tezgah MengenesiTezgah Mengenesi
Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Kurbağacık anahtarKurbağacık anahtar
Koruyucu gözlükKoruyucu gözlük
6

Spring bars, motor and belt

Bend two strips of spring steel 37, 30 x 3 mm, with a slight bend near one end, and bolt them under the cross bar 28 so they reach out beyond the trunnions. Bolt the motor 36 to them, with cap nuts 40 on the bolts' ends: these are its feet when the unit stands alone. Fit a V-belt pulley 42 on the motor and one 44 on the arbor, and the A-section belt 43. Pivot an arm 45 on the arbor's bearing with a weighted pulley 46 at its free end resting on the belt to take up the slack. Have the motor wired to a switch.

Bu adım için malzemeler:

Yay çeliği şeridiYay çeliği şeridi1 adet
Elektrik motoruElektrik motoru1 adet
V kayış kasnağı (A kesit)V kayış kasnağı (A kesit)3 adet
V kayış (A kesiti)V kayış (A kesiti)1 adet
Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı6 adet
Altıgen SomunAltıgen Somun6 adet
Çukur uçlu setuskurÇukur uçlu setuskur3 adet
Açma/kapama anahtarıAçma/kapama anahtarı1 adet

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
Alyan takımıAlyan takımı
7

Put the unit in and set the saw

Fit the 200 mm blade on the arbor. Hang an M10 screw 32 from arm 34 with its head 35 on top. Lower the power unit in, the trunnions into the notches 30 and the forked lug 31 round the screw, and run a wing nut 36 up under the lug. Turn the wing nut to raise the blade through the opening to the depth wanted.

Bu adım için malzemeler:

Circular Saw Blade SetCircular Saw Blade Set1 adet
Dişli milDişli mil1 adet
Kanatlı somunKanatlı somun1 adet
Düz PulDüz Pul2 adet

Gerekli aletler:

Kurbağacık anahtarKurbağacık anahtar
8

Follower and rip guide

Angle follower: a hardwood bar 17 sliding in the groove, with an angle fence 18 clamped at any angle by a wing nut 19. Rip guide 20: a hardwood bar across the platform held by two hook bolts 21 that hook under the flange 8, with wing nuts 22. Mark a scale 23 on the platform's ends to set it.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Dişli milDişli mil1 adet
Kanatlı somunKanatlı somun3 adet
Yumuşak Çelik LamaYumuşak Çelik Lama1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Tezgah MengenesiTezgah Mengenesi
Şerit MetreŞerit Metre
9

Try it, and as a grinder

With the platform flat, check the blade is square to it with the square, rip a board along the guide and crosscut another against the follower. Tilt the platform with the tilt screw (and the block under it for steep angles) and check the angle with the protractor. Lift the power unit out, stand it on its cap nuts, swap the blade for the grinding wheel, swing the idler arm to the belt's other side, and run it.

Gerekli aletler:

Taşlama taşıTaşlama taşı
Kombine GönyeKombine Gönye
İletkiİletki
Koruyucu gözlükKoruyucu gözlük
Kulak koruyucu (kulaklık, SNR 30 dB)Kulak koruyucu (kulaklık, SNR 30 dB)
10

Troubleshooting

Portable bench saw troubleshooting.

Flow

Loading...
11

History and honest limits

**Fay M. Henkel** of New Rochelle, New York, US 1,695,188, dated 11 December 1928, filed 28 April 1927. He claimed a supporting unit with a platform and a power unit with a frame, "trunnions on the end of said frame, said supporting unit having recesses therein receiving the trunnions", a bearing and arbor, spring bars and a motor fixed to them, pulleys and a belt; and the spring bars' couplings serving as feet when the unit is removed. His frame, platform and legs are castings; ours are hardwood, plywood and steel. His bearing is a sleeve with a grease cup; ours are two greased flange bearings. He gives no sizes, motor or speeds; those are ours.

Malzemeler

22

Gerekli Aletler

24

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...