İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)
Forge

Oluşturan

Forge

4. Kasım 2026NO
14
0
0
1
0

Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)

Cornelius Whitehouse's way of making welded iron tubes, the basis of butt-weld pipe ever since: a strip of flat iron is turned up into a tube with its edges meeting, heated nearly to fusion in a hollow fire, and pulled by the chain of a draw bench through a pair of dies, which press the hot edges together and weld them. The tube is welded in two halves, one end at a time. Whitehouse made tubes 2 to 8 ft long in one piece, smooth inside and out. Unknown: plate thickness, width and tube sizes. The source does not give them. Source: Whitehouse's specification of 1825, quoted in C. D. Terry, Butt Weld Pipe (1907). Picture: Terry's Figs. 4 and 5.
İleri
Unknown

Talimatlar

1

Turn the plate over

Take a piece of flat iron (plough-plate iron) of a thickness and width to suit the intended bore. Bend up its sides ('turn it over') until the edges meet, or nearly so, and it forms a long tube. Ours: hammer and anvil for the bending.

Bu adım için malzemeler:

Dövme demir çubuklarDövme demir çubuklar1 flat plough-plate iron
Bilinmeyen ölçülerBilinmeyen ölçüler1 adet

Gerekli aletler:

Dövme ÇekiciDövme Çekici
Düz örsDüz örs
2

Heat in the hollow fire

Put the tube into a hollow fire, urged by a blast, and heat it until the iron is on the point of fusion. Ours: a smith's forge as the hollow fire.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Demirci MaşasıDemirci Maşası
3

Draw it through the dies

Clamp the end of the tube to the chain of the draw bench, driven by a hand winch or an engine. Draw it out of the fire through a pair of dies of the size wanted, set in a screw press and closed to their bearing, so that the hot edges are pressed together and welded. A pair of pinchers with a conical hole, held against a standard, may be used instead of the press and dies.

Gerekli aletler:

Çekme tezgâhıÇekme tezgâhı
Demirci MaşasıDemirci Maşası
4

Weld the other half

Open the clamp and take the tube off. Grip the other end, put the unwelded part into the fire, heat it, and draw it through the dies in the same way.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Çekme tezgâhıÇekme tezgâhı
Demirci MaşasıDemirci Maşası

Malzemeler

2

Gerekli Aletler

5

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...