İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Keyway Broaching: Tooth Pitch, Rise per Tooth, Rake and Clearance by Metal and Hardness, Pushing Force
Cut a keyway in a bore with a keyway broach in an arbor press, and work out the broach criteria for your metal: tooth pitch and teeth in contact, rise per tooth and the number of teeth, rake and clearance by material and hardness, and the pushing force. Rules from Machinery's Handbook (1924), Hammond (1921), the US Navy and Metcut (1980).
Orta
About 1 hour per part
Talimatlar
1
1
How a keyway broach cuts
How a keyway broach cuts
The broach slides through a slotted bushing in the bore. Each tooth stands a little higher than the one before (the rise), so each takes a thin chip and the keyway deepens tooth by tooth; the last teeth are the finished size and only clean up. Shims behind the broach set the depth for the next pass. Our animation; the rise is exaggerated.

2
2
Tooth pitch and teeth in contact
Tooth pitch and teeth in contact
Jupyter defteri yükleniyor…
3
3
Rise per tooth by metal
Rise per tooth by metal
Jupyter defteri yükleniyor…
4
4
Rake and clearance by hardness
Rake and clearance by hardness
Jupyter defteri yükleniyor…
5
5
Pushing force (estimate)
Pushing force (estimate)
Jupyter defteri yükleniyor…
6
6
Check the work hardness
Check the work hardness
Test the hub. Metcut's angles are by Brinell. For steel Hammond wants scleroscope 32-40: softer tears, harder "will rapidly destroy the broaches". He gives no Brinell or Rockwell figure; convert with a standard table (ASTM E140) if you test in Rockwell.
Gerekli aletler:
Rockwell sertlik ölçüm cihazı7
7
Bore and bushing
Bore and bushing
The bore must be to size: the broach's pilot should enter freely but not let the broach drop past the first tooth. Fit the bushing snug in the bore, slot where the keyway goes.
Bu adım için malzemeler:
Deliği işlenmiş göbek taslağı1 adetGerekli aletler:
Kama kanalı broşu kılavuz burcu
Kumpas8
8
Set up in the press
Set up in the press
Set hub, bushing and broach square under the arbor press, rigid and true. Oil the broach: broaching oil is best; lard or soluble oil will help.
Gerekli aletler:
Kollu pres
Kama kanalı broşu
Kesme yağı9
9
Push it through
Push it through
Push with slow, even pressure. Never bring the broach back up through the hole: push it on through and catch it on a soft cushion.
Gerekli aletler:
Kollu pres
Pamuklu Bez10
10
Shim and repeat
Shim and repeat
Put the next shim behind the broach to set the next depth, oil, and push through again. Repeat until the keyway is deep enough.
Gerekli aletler:
Broş şimi
Kesme yağı11
11
Measure the keyway
Measure the keyway
Check the width and the depth from the opposite side of the bore.
Gerekli aletler:
Kumpas
Mikrometre12
12
Troubleshooting
Troubleshooting
Broaching problems and fixes.
Flow
Loading...
13
13
Sources and honest limits
Sources and honest limits
*Machinery's Handbook* 6th ed. (1924) pp. 1135-1137 (first printed in Jones, *Broaching*, 1914); Hammond, *Broaching Practice* (1921) pp. 6, 7, 44; US Navy, *Machinery Repairman 3 & 2* (1990) p. 3-24; Metcut, *Machining Data Handbook* 3rd ed. (1980) Table 15.16 and pp. 17-8 to 17-20, © Metcut, cited. Not in any source we could read: cutting speed by hardness (Hammond gives 5-6 ft/min for 1921 carbon-steel broaches) and a Brinell or Rockwell limit. The force formula is our derivation. Ours: the animation, the example sizes.
Malzemeler
1- Yer Tutucu
Gerekli Aletler
9- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

