İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
Buttercup

Oluşturan

Buttercup

10. Kasım 2026IE
13
0
0
0
0

Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter

S. S. Langdon of Cleveland, Ohio, received US 25,126, dated 16 August 1859, for a rotary churn shaped like a common box. It turns on two journals in a frame. Inside, two zinc partitions set into saw kerfs make a cream chamber in the middle and two water chambers at the ends, for warm or cold water to temper the cream. A dash-frame of bars, held by a spring, sits midway while churning and is lowered to the bottom so the butter comes out without being pulled through it. Langdon gives no sizes; every size here is ours, and stainless steel stands in for his zinc.
Orta
About 2 days

Talimatlar

1

How much cream, how much water

Jupyter defteri yükleniyor…
2

A box churn tempered with water, before it

Langdon knew a box churn with water chambers had been used without a dasher. He added the dash-frame.
3

Read US 25,126

"When churning, I place the dash-frame about midway from the top to the bottom of the churn, as shown in Fig. 2. When the operation of churning is completed the dash-frame may be lowered to the bottom of the churn in order to remove the butter without interfering with the latter or causing it to adhere to the dasher".
4

Box and kerfs

From 19 mm hardwood cut a bottom 440 x 278 mm, two sides 440 x 240 mm and two ends 240 x 240 mm. Saw a kerf 1 mm wide and 6 mm deep across each side and the bottom, 150.4 mm either side of the middle, for the partitions. Glue and screw the ends between the sides and the box onto the bottom, square.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar24 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Çubuklu işkenceÇubuklu işkence
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
5

Partitions F and the water chambers E

Cut two stainless sheet plates 251 x 245 mm, 0.8 mm thick, and slide them down the kerfs: each closes off a water chamber 50 mm long at an end. Drill a 17 mm hole low in each end board and one in the bottom of the cream chamber, for the plugs. Fill the box with water overnight so the wood swells tight round the plates; check that each water chamber holds water without filling the cream chamber, then empty it.

Bu adım için malzemeler:

Paslanmaz çelik levhaPaslanmaz çelik levha1 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

Sac makasıSac makası
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
SuSu
FDM 3B yazıcıFDM 3B yazıcı
6

Print the plugs L

A tapered plug 18 mm at the head, 25 mm long. Print three. PETG, 0.2 mm layers, 100 % infill.
Tasarım DosyasıSTLCC0 - Free
7

Dash-frame K and spring K'

Cut two hardwood rails 296 x 44 x 20 mm and seven bars 20 x 20 x 196 mm. Fix the bars between the rails set diamond-wise, one corner up, as Fig. 2 draws, 37 mm apart, glued and screwed through the rails. Rivet or screw a bowed strip of stainless spring steel, 256 mm long, along the outside of one rail so it presses on the side and holds the frame wherever you set it.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Soğuk haddelenmiş paslanmaz çelik şerit (420)Soğuk haddelenmiş paslanmaz çelik şerit (420)1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar14 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Sac makasıSac makası
8

Cover G, journals B, frame A and crank C

Cut the cover from 12 mm plywood to the box's outside size. Set four 6 mm bolts head down in the sides' top edges, 75 mm either side of the middle, through matching holes in the cover, with wing nuts on top. Glue and screw a hardwood block 80 x 80 x 40 mm to the middle of each end, bore it 20 mm, drive in a 20 mm steel stub and pin it with a bolt across. Build a pine frame on four posts with open slots in its top rails for the stubs, and a crank with a turned handle on one stub outside the frame.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı6 adet
Kanatlı somunKanatlı somun4 adet
Düz PulDüz Pul4 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ham çelik çubukHam çelik çubuk1 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm2 adet
Çam tahtaÇam tahta1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar24 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Kurbağacık anahtarKurbağacık anahtar
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
9

The build in 3D

FreeCAD model of this build, cover and one side cut away: the cream chamber between the stainless partitions, the water chambers at the ends with their plugs, the dash-frame of diamond-set bars midway, the journal blocks, the frame and the crank. The box was turned through 16 angles in the frame.
Tasarım DosyasıBLENDCC0 - Free
10

Temper and churn

Fill both water chambers with warm or cold water as needed, checked with the thermometer, and plug them. Set the dash-frame midway, pour in about 5 litres of heavy cream, bolt the cover on and turn the crank steadily, timing it. When the butter comes, take the cover off, push the dash-frame down to the bottom, lift the butter out over it and drain the buttermilk at the bottom plug. Wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema5 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
Elektrikli su ısıtıcısıElektrikli su ısıtıcısı
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
11

Troubleshooting

Water-chamber churn troubleshooting.

Flow

Loading...
12

History and honest limits

**S. S. Langdon** of Cleveland, Ohio, US 25,126, 16 August 1859, "Churn". He claimed his construction and arrangement of rotary churns with the dash-frame K and the water chambers E. He gives no sizes, so every size here is ours. Stainless steel replaces his sheet zinc because the cream and buttermilk touch the partitions; four wing-nut bolts are his "thumb screws placed on the edge of the cover"; the spring strip and the journal blocks are our versions of his spring K' and journals B.

Malzemeler

17

Gerekli Aletler

19

Tasarım dosyaları

2

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...