İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
Forge

Oluşturan

Forge

4. Kasım 2026NO
13
0
0
1
0

Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)

A lathe turning tool ground from tool steel bar. Three things decide how well it cuts: the shape of the edge seen from above, the clearance under the edge, and the slope of the top the chip slides over. The Handbook gives the angles for each kind of metal to be turned. Variable: the metal to be turned. Clearance 8 to 10° for general work, 12 to 14° for brass. Soft steel: back slope 8°, side slope 14 to 20°. Very hard steel: 5° and 9°. Brass: flat on top. Source: Machinery's Handbook (1924), pp. 887-889, Tool Grinding. Unknown: the steel and the bar size. Picture: the Handbook's figure.
Orta
Unknown

Talimatlar

1

Choose the edge shape

Grind the edge, seen from above, to suit the job. A large-radius edge roughs and keeps its edge at higher speed; a smaller point is better on flexible work that would chatter. A parting tool must be widest at the cutting edge so it does not bind in its groove. Ours: square tool steel bar. Not given: the steel, the bar size.

Bu adım için malzemeler:

Kare takım çeliği çubukKare takım çeliği çubuk1 tool blank

Gerekli aletler:

Bileme taşı çarkıBileme taşı çarkı
SuSu
2

Grind the clearance and the slope

Grind clearance under the edge: 8 to 10° for general turning, 12 to 14° for brass and soft metals; too much weakens the edge. Slope the top away from the working part of the edge. A roughing tool for medium or soft steel gets a back slope of 8° and a side slope of 14 to 20°; for very hard steel, 5° and 9°. A broad finishing tool slopes straight back. Thread tools and tools for brass or chilled iron are flat on top; very hard metals get almost no slope and little clearance. Roughing tools cut fastest with a lip angle near 61°, but cast iron cuts better at about 68°.

Gerekli aletler:

Bileme taşı çarkıBileme taşı çarkı
İletkiİletki
3

Grind without burning

Press the tool only moderately against the wheel and draw it away often, especially when grinding a broad flat face, so the edge does not overheat and burn. Keep the wheel supplied with plenty of cooling water.

Gerekli aletler:

Bileme taşı çarkıBileme taşı çarkı
SuSu

Malzemeler

1

Gerekli Aletler

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...