İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Oluşturan

Forge

13. Kasım 2026NO
4
0
0
0
0

Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat front horseshoe made from one iron bar, as taught at the Dresden shoeing school: bend each branch over the anvil, bevel and flatten it, concave the hoof side, fuller the crease, and stamp and pritchel the nail holes. From Lungwitz and Adams, A Text-Book of Horseshoeing (11th edition, 1913). "Any ordinary shoe can and should be completed in the rough in two heats." Fitting and nailing the shoe to the horse are not covered here.
Orta
8-15 minutes a pair, once practised

Talimatlar

1

Bar length and sizes

Jupyter defteri yükleniyor…
2

Read Lungwitz and Adams

"A shoe should be made thoughtfully, but yet quickly enough to make the most of the heat."
3

Measure the hoof

Measure the length of the hoof from the point of the toe to the buttress, and its greatest width. Added together they give the length of the bar. To keep the exact outline, set the hoof on stiff paper and trace round the wall with a pencil.

Gerekli aletler:

Şerit MetreŞerit Metre
Kurşun kalemKurşun kalem
Kalın kâğıt tabakalarıKalın kâğıt tabakaları
4

Cut the bar

Choose good, tough iron, of a width and thickness that needs the least working. Cut the bar to the length you measured; a bar shoe or a shoe with heel calks needs a longer bar.

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
Örs kesme keskisiÖrs kesme keskisi
Demirci MaşasıDemirci Maşası
Yuvarlatma çekiciYuvarlatma çekici
5

Bend the outer branch

Heat the bar white-hot just beyond its middle. Lay the head of the sledge across one end of the anvil face, hold the cold end of the bar on it with the hot end on the face, and bend the bar into a half-circle with the round head of the turning hammer. Make the outer branch first, and the right shoe first in a pair. Draw out the end to width and thickness with the sledge.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Gagalı örsGagalı örs
Yük kızağıYük kızağı
Yuvarlatma çekiciYuvarlatma çekici
Demirci MaşasıDemirci Maşası
6

Bevel and flatten

Lay the bent branch obliquely across the heel of the horn, turn it to the right onto an edge, and bevel it diamond-shaped from toe to end. Flatten it on the face: bending stretched and thinned the outer edge and thickened the inner one, so leave the inner edge a trifle thinner. Go over it lightly on the horn with the flat face of the hammer to shape it.

Gerekli aletler:

Gagalı örsGagalı örs
Yuvarlatma çekiciYuvarlatma çekici
Demirci MaşasıDemirci Maşası
7

Concave and fuller

Concave (seat) the hoof side, ending about 3/4 in from the end of the branch, or leave it flat for an arched sole. Turn the branch and fuller it: set the fuller about 1/12 in from the edge on small shoes, more on large ones, and lead it from the end of the branch to the toe, twice, to about two-thirds of the thickness.

Gerekli aletler:

Gagalı örsGagalı örs
Yük kızağıYük kızağı
Fuller (oluk açma demiri)Fuller (oluk açma demiri)
Yuvarlatma çekiciYuvarlatma çekici
Demirci MaşasıDemirci Maşası
8

Stamp and pritchel the nail holes

Stamp the nail holes in the crease and punch them through with the pritchel. Six are enough for a medium shoe, all in the front half and none at the toe. Their distance from the outer edge equals the thickness of the wall there; incline the toe holes a little inward and punch the quarter holes straight. Each hole tapers from the ground side to the hoof side.

Gerekli aletler:

Gagalı örsGagalı örs
Sıcak zımbaSıcak zımba
Nal delme zımbasıNal delme zımbası
Yuvarlatma çekiciYuvarlatma çekici
Demirci MaşasıDemirci Maşası
9

Finish the branch, then the other

Run over the surfaces, go over the outer edge on the horn, and hammer the bearing surface smooth and level. Make the inner branch the same way, turned to the left and fullered from toe to heel. The finished front shoe is round at the toe and about 7/16 in thick; a hind shoe is bent more pointed at the toe and needs no concaving, only the inner edge rounded.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Gagalı örsGagalı örs
Yuvarlatma çekiciYuvarlatma çekici
Fuller (oluk açma demiri)Fuller (oluk açma demiri)
Sıcak zımbaSıcak zımba
Nal delme zımbasıNal delme zımbası
Demirci MaşasıDemirci Maşası
10

Troubleshooting

Horseshoe troubleshooting.

Flow

Loading...
11

History and honest limits

From **A Text-Book of Horseshoeing, for Horseshoers and Veterinarians**, by A. Lungwitz (Dresden shoeing school) and John W. Adams (University of Pennsylvania), 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F, "Making Shoes"; wall thicknesses after Mayer. Not covered: trimming, fitting and nailing the shoe to the hoof, clips, calks and special shoes. The book names no forge fuel. The metric figures are ours.

Malzemeler

1

Gerekli Aletler

12

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...