SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
YEŞİL GELECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Making a Color-Changing LilyPad Patch
Ed

Oluşturan

Ed

13. Temmuz 2026FI
0
0
0
0
0

Making a Color-Changing LilyPad Patch

Sew a patch that glows in any color. A single RGB LED holds red, green and blue elements; by fading each one with the microcontroller's PWM pins you mix millions of colors and cycle through the rainbow. The e-textile version of the classic RGB colour-mixing project.

Orta
1-2 hours

Talimatlar

1

Sew the board and RGB LED

Sew a LilyPad Arduino onto felt. The RGB LED has four legs — bend each into a small loop so it can be sewn. Wire the common cathode (the longest leg) to -, and the red, green and blue legs to pins 5, 6 and 9. Keep the four lines from touching each other.

Bu adım için malzemeler:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 adet
LED - RGB Diffused Common Cathode - 5mmLED - RGB Diffused Common Cathode - 5mm1 adet
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 makara
Hand Sewing Needles (Assorted, 30-Pack)Hand Sewing Needles (Assorted, 30-Pack)1 paket
Wool Felt SheetWool Felt Sheet1 yaprak
2

Connect the programmer

Plug the LilyPad FTDI onto the programming header and connect the USB cable. Open the Arduino IDE and select the LilyPad Arduino board and its serial port.

Bu adım için malzemeler:

LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V1 adet
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 adet

Gerekli aletler:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the color-mixing sketch

Paste this sketch and upload. It fades the LED through red, green, blue and the mixes using analogWrite (PWM).

lilypad_color_changing.inoarduino
// Mix colors on a common-cathode RGB LED.
// Red/Green/Blue legs on PWM pins 5, 6, 9; common cathode to - (GND).

const int RED_PIN = 5;
const int GREEN_PIN = 6;
const int BLUE_PIN = 9;

void setColor(int r, int g, int b) {
  analogWrite(RED_PIN, r);     // 0 = off, 255 = full
  analogWrite(GREEN_PIN, g);
  analogWrite(BLUE_PIN, b);
}

void setup() {
  pinMode(RED_PIN, OUTPUT);
  pinMode(GREEN_PIN, OUTPUT);
  pinMode(BLUE_PIN, OUTPUT);
}

void loop() {
  setColor(255, 0, 0);   delay(500);  // red
  setColor(0, 255, 0);   delay(500);  // green
  setColor(0, 0, 255);   delay(500);  // blue
  setColor(255, 255, 0); delay(500);  // yellow
  setColor(0, 255, 255); delay(500);  // cyan
  setColor(255, 0, 255); delay(500);  // magenta
  setColor(255, 255, 255); delay(500);// white
}
4

Watch it cycle, then mix your own

The LED fades through the colors on its own. Make your own by changing the three numbers in setColor(red, green, blue) — each 0–255. Note: at the LilyPad's lower voltage blue and green look a little dimmer than red, which is normal for RGB LEDs.

5

Go wireless and wear it

Plug a 3.7 V LiPo into the LilyPad Arduino's JST connector and switch on — the higher voltage also makes the colors brighter. Sew the felt onto a bag or costume for a colour-changing glow.

Bu adım için malzemeler:

LiPo Battery 3.7V 1000mAh (JST Connector)LiPo Battery 3.7V 1000mAh (JST Connector)1 adet

Malzemeler

8

Gerekli Aletler

1
Tahmini toplam
$110.00

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Blinking an LED with LilyPad ArduinoEd tarafından
Driving an RGB LED — SIK Circuit 3Ed tarafından

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Making a Motion-Reactive LilyPad Patchelectronics
Making a Sound-Triggered LilyPad Patchelectronics
Making a LilyPad Musical Patchelectronics
Making a LilyPad Night-Lightelectronics
Blinking an LED with LilyPad Arduinoelectronics
Using an LCD — SIK Circuit 15electronics

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...