İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately
Martin

Oluşturan

Martin

9. Kasım 2026NO
13
0
0
0
0

Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately

James O. Merrill of Chichester, New Hampshire, received US 23,986, dated 10 May 1859, for an oscillating churn light enough to be worked by a child. A weighted pendulum behind the frame rocks a shaft; on its front end a beam rocks, and two links from the beam's ends work two dasher arms up and down in turn through slots in a guide bar. Each arm carries a half-round dasher pierced with holes, so the two halves fill the barrel. The two-piece cover is held down by a thumb screw. This rung builds it full size in timber over a 20-litre bucket.
Orta
About 2 days

Talimatlar

1

How far the dashers move

Jupyter defteri yükleniyor…
2

Two dashers worked in turn, before it

Mitchell's lever worked two dashers in turn; Merrill's weighted pendulum keeps them going with less effort.
3

Read US 23,986

"... the operator oscillates the lever L, which communicates the motion through the vibrating shaft M, the vibrating lever E, the auxiliary levers F, F', to the dasher arms G, G', thus producing an alternate reciprocating action of the dashers N, N'".
4

Base and frame

Cut a pine base A 720 x 520 mm. Stand two side pieces B B' of 44 x 70 mm timber 960 mm tall, 400 mm apart, 200 mm from the base's back edge, with diagonal side braces I I' and front braces H H' to the base. Screw top braces C C' (444 x 60 x 22 mm) across the front and back faces of the side pieces at the top, and bore both 21 mm in the middle, 30 mm below their top edge.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm4 adet
#10 x 3" ahşap vidası#10 x 3" ahşap vidası30 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
İşkencelerİşkenceler
Su TerazisiSu Terazisi
Şerit MetreŞerit Metre
5

Shaft M, lever E and pendulum L

Screw a hardwood bearing block 80 x 80 x 18 mm, bored 20.5 mm, over each hole. Cut a 20 mm steel shaft 310 mm long and pass it through both. On its front end fix a hardwood lever E 400 x 60 x 20 mm at its middle with a bolt across, drilled 8.5 mm 150 mm each side of the middle for the pins c. On its back end fix the pendulum L, a hardwood bar 50 x 20 mm, 810 mm long, 60 mm below its top. Glue a 24 mm dowel handle h into L 180 mm below the shaft and bolt an 8 kg kettlebell to its foot as W.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Ahşap vidalarAhşap vidalar8 adet
Ham çelik çubukHam çelik çubuk1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı3 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu3 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
KettlebellKettlebell1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Demir TesteresiDemir Testeresi
Kurbağacık anahtarKurbağacık anahtar
6

Guide bar J, arms G and links F

Bolt a hardwood guide bar J 444 x 40 x 36 mm across the side pieces' fronts on spacer blocks so it stands 70 mm in front of them, 530 mm above the base, and cut two 27 mm square slots through it 40 mm apart. Cut two hardwood dasher arms G G' 25 mm square and 580 mm long, drop them through the slots, and drill each 8.5 mm 20 mm below its top. Cut two links F F' 30 x 14 mm with holes 282 mm apart and bolt each from a pin c on E to a pin g on an arm, with washers and lock nuts so they turn freely.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı6 adet
Düz PulDüz Pul8 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu4 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
7

Barrel D, covers, dashers and thumb screw

Stand a food-grade 20-litre bucket on the base under the arms. Cut two half-discs N N' 240 mm across from 12 mm plywood, each with three 34 mm holes, and screw one under each arm's foot. Cut two half-round covers m m from 12 mm plywood to fit the bucket's top, notched for the arms. Bolt a cross brace K 444 x 40 x 30 mm across the side pieces' fronts 440 mm above the base, drill it for an M8 rod 72 mm behind the arms, and run the rod through a nut in K with a wing nut on top as the thumb screw i, down onto an oblong block l laid across both covers.

Bu adım için malzemeler:

20 Litrelik Kova20 Litrelik Kova1 adet
Kontrplak levhaKontrplak levha2 adet
Ahşap vidalarAhşap vidalar6 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı2 adet
Dişli milDişli mil1 adet
Altıgen SomunAltıgen Somun1 adet
Kanatlı somunKanatlı somun1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Panç testere setiPanç testere seti
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
Kurbağacık anahtarKurbağacık anahtar
8

The build in 3D

FreeCAD model of this build, a quarter of the barrel and covers cut away: the base and frame with its braces, shaft M with lever E in front and the weighted pendulum behind, links F, the arms in guide bar J, the two half-dashers in the barrel, and the thumb screw on its block. It was checked at five pendulum angles from -12 to +12 degrees.
Tasarım DosyasıBLENDCC0 - Free
9

Churn

Lift the front cover, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, put the cover back and turn the thumb screw down on the block. Swing the pendulum by its handle about 12 degrees each way and time it: the half-dashers rise and fall in turn. When the butter comes, slacken the screw, unbolt the dashers, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**James O. Merrill** of Chichester, Merrimack County, New Hampshire, assignor to Wm. A. Swain, US 23,986, 10 May 1859, "Churn". He meant it to take the labour out of churning, adapted to the strength of a child, and claimed the pendulum and weight with the shaft, beam, links and the two alternate dasher arms. He gave no sizes or weight: the frame, the 8 kg weight, the 12 degree swing and every size are ours.

Malzemeler

20

Gerekli Aletler

17

Tasarım dosyaları

1

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...