İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)
Spartan

Oluşturan

Spartan

13. Kasım 2026NO
9
0
0
0
0

Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)

C. M. Miller's dragon kite from The Boy Mechanic, Book 3 (1919): a 12 in bamboo-ring head with horns and two paper eyes that spin in the wind, followed by up to 20 round section kites, each with a 36 in balancer stick, tied 30 in apart on three cords of seine twine. Twenty sections make a kite about 50 ft long.
İleri
Several days

Talimatlar

1

Strip lengths and kite length

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 3

"Dragon kites are made as hideous as the maker can possibly conceive, and while the one to be considered is no beauty, it is more droll than fierce-looking."
3

Split and pare the bamboo

Split bamboo into strips about 3/16 in wide and pare them to less than 1/16 in thick for the head's inner ring A. To bend a strip to a sharp angle, heat it over a candle flame until it gives under pressure, bend it, and it keeps its shape when cold.

Bu adım için malzemeler:

Bambu sırıklarBambu sırıklar1 adet

Gerekli aletler:

Çelik çakıÇelik çakı
MumMum
4

Frame the head

Make ring A 12 in across from a strip about 38 in long, lapping the ends and winding them with linen thread (or with wet pasted strips of rice paper about 1/2 in wide, which bind as they dry). Lash two crosspieces B and C of the same stock 3-1/2 in apart, parallel and equally spaced from the centre, their ends bent sharply and lashed inside the ring. Lash two eye rings D and E, 3-1/2 in across, between them, shaped round a 3-1/2 in cylinder so they are true. Lash stiffeners F and G, 1/16 by 1/8 by 20 in, across the back. Add outer ring H, 3 in outside A (18 in across), of 1/8 in strip under 1/16 in thick, in two pieces if needed, and the short pieces J and K between the rings. Lash the horn supports, 1/8 in wide, to the upper crosspiece and both rings, with L and M halfway between the ends of F and G and radiating from the centre of A, and N and O pointing at the eye-ring centres (Fig. 2).

Bu adım için malzemeler:

Bambu sırıklarBambu sırıklar1 adet
Keten iplikKeten iplik1 adet

Gerekli aletler:

Çelik çakıÇelik çakı
MumMum
Şerit MetreŞerit Metre
MakasMakas
5

Cover and paint the head

Cover only the inside of ring A, the horns and the ears with Chinese rice paper, stretched tight with no bagging, leaving the eye rings open. Put the rings on the horns and stick ends, 1/2 to 2 in across, cut from stiff paper (larger ones of bamboo). Shade with a brush and water colours, leaving the face white or tinting it; leave the horns white and colour the tongue red (Fig. 1).

Bu adım için malzemeler:

Pirinç kâğıdıPirinç kâğıdı1 adet
Buğday tutkalıBuğday tutkalı1 adet
Bristol KartonBristol Karton1 adet
SuluboyaSuluboya1 adet

Gerekli aletler:

Tutkal fırçasıTutkal fırçası
Ressam fırçası setiRessam fırçası seti
MakasMakas
6

Make the revolving eyes

Pare bamboo to 1/32 in and form each eye into a true ring 3-1/4 in across. Pass a wire axle exactly on a diameter through the eye ring and through its socket ring D or E, with a glass bead on the wire each side between the two rings; fix the wire to the eye ring with a strip of paper wrapped tight and pasted. Cover each side halfway with rice paper, the front upper half and the back lower half, so the wind turns the eye. Blacken the front upper half and paste a round pupil between the halves so it shows on both sides (Figs. 3, 4).

Bu adım için malzemeler:

Bambu sırıklarBambu sırıklar1 adet
Demir telDemir tel1 adet
Cam boncukCam boncuk4 adet
Pirinç kâğıdıPirinç kâğıdı1 adet
Buğday tutkalıBuğday tutkalı1 adet
SuluboyaSuluboya1 adet

Gerekli aletler:

Çelik çakıÇelik çakı
Yassı Ağızlı PenseYassı Ağızlı Pense
MakasMakas
Ressam fırçası setiRessam fırçası seti
7

Make the section kites

For each section make a 12 in ring of bamboo 1/8 in wide and 1/16 in thick and cover it tight like the head. Lash on a balancer stick 36 in long, small, light and well balanced, at about the place of cross-stick F, with tufts of tissue paper or feathers at its tips. Colour the discs as you like; give the last section's balancer streamers of light cloth (Figs. 5, 6). Sections may instead be 9 in with 30 in balancers, but uniform sections are better and easier.

Bu adım için malzemeler:

Bambu sırıklarBambu sırıklar1 adet
Keten iplikKeten iplik1 adet
Pirinç kâğıdıPirinç kâğıdı1 adet
Buğday tutkalıBuğday tutkalı1 adet
Renkli pelür kâğıdıRenkli pelür kâğıdı1 adet
TüylerTüyler1 adet
Pamuklu BezPamuklu Bez1 adet
SuluboyaSuluboya1 adet

Gerekli aletler:

Çelik çakıÇelik çakı
MumMum
MakasMakas
Ressam fırçası setiRessam fırçası seti
8

Tie the harness and bridle

Cut three cords of six-ply hard-twisted seine twine as long as the kite plus the knots. Fasten the head to a wall, tie the three cords to it at T, U and V (Fig. 2), and tie each section at the matching points exactly 30 in from the last (Fig. 7). Tie a three-string bridle to the head at T, U and V, the lower string longer than the two upper ones so the head, and with it every section, leans to the wind. A ball balancer of bamboo strips may hang from the head (Fig. 8).

Bu adım için malzemeler:

Ağ ipiAğ ipi1 adet
Uçurtma ipiUçurtma ipi1 adet
Bambu sırıklarBambu sırıklar1 adet

Gerekli aletler:

Şerit MetreŞerit Metre
MakasMakas
9

Flying and troubleshooting

Dragon kite flying.

Flow

Loading...
10

History and honest limits

From "How to Make Combined Kites, Part I: A Dragon Kite" by C. M. Miller, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 145-148). He gives no bridle lengths and no line size beyond "a strong cord". Fig. 2 also marks 5 in at the horn tip and 1 in where F passes ring H. The tools and metric figures are ours.

Malzemeler

13

Gerekli Aletler

7

Bu planla yapılan

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...