İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Milling Vise: Swivelled on a Two-Face Base with a Cone Seat and Locking Shoes (McClellan, US 652,441)
Forge

Oluşturan

Forge

9. Kasım 2026NO
11
0
0
0
0

Milling Vise: Swivelled on a Two-Face Base with a Cone Seat and Locking Shoes (McClellan, US 652,441)

A milling vise holds the work on the table of a milling machine: a fixed jaw, a jaw moved by a screw, and a base that lets the vise swivel to any angle. E. J. McClellan (US 652,441, 1900) turns the vise on a cone-shaped disk in a matching seat in a cylindrical base, reads the angle on a scale, and locks it with two shoes screwed against the cone. His base has two planed faces at right angles, each with its own bolt slots, so the vise can be bolted to the table lying flat or standing upright. Source: E. J. McClellan, "Milling-Machine Vise", US Patent 652,441 (1900). Picture: its Figs. 1-3.
İleri
Unknown

Talimatlar

1

Read McClellan

"With such a construction it is possible to support the vise in one plane only, which plane is horizontal; but it is often found desirable to mount the vise in an upright position upon the slide in order to use the machine to the best advantage".
2

Make the base

Make a cylindrical block. Plane one end face square to its axis to fit the machine table, with two ears at opposite points, slotted for bolts parallel to the axis. Give it a side extension with a second planed face at right angles to the first and parallel to the axis, with its own slotted ears, so the base can be bolted down on its end or on its side. Mark a scale round part of the opposite end face. Sizes, metal and how the scale is cut are not given.

Bu adım için malzemeler:

Bilinmeyen metalBilinmeyen metal1 base

Gerekli aletler:

Metal planya tezgâhıMetal planya tezgâhı
Eğeler (El Eğesi)Eğeler (El Eğesi)
Bilinmeyen ölçülerBilinmeyen ölçüler
Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
3

Cut the cone seat

Bore a large central opening through the base and turn the end next to the scale into a conical seat, narrowest at the scaled face. Turn a disk with a matching conical edge. Drill two radial holes into the seat, ninety degrees apart, fit a shoe in each whose face forms part of the cone, and tap the holes behind them for adjusting screws.

Bu adım için malzemeler:

Bilinmeyen metalBilinmeyen metal1 disk
Bilinmeyen metalBilinmeyen metal2 shoes

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
4

Make the vise

Make a plate carrying a fixed jaw, and a second plate as the sliding jaw, fitted to slide on the first and moved by a screw. Put an index mark on the vise to read against the base scale. The vise may be of any good construction; its sizes and the screw's thread are not given.

Bu adım için malzemeler:

Bilinmeyen metalBilinmeyen metal1 plate and fixed jaw
Bilinmeyen metalBilinmeyen metal1 sliding jaw
Bilinmeyen metalBilinmeyen metal1 screw

Gerekli aletler:

Metal planya tezgâhıMetal planya tezgâhı
Metal Torna TezgâhıMetal Torna Tezgâhı
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Bilinmeyen ölçülerBilinmeyen ölçüler
5

Assemble and set

Pass the disk into its seat from below and bolt it to the vise plate with a centre bolt and an off-centre bolt. Bolt the base to the table on whichever face suits the job. To set an angle, slacken the bolts, swivel the vise to the scale, and screw the two shoes hard against the cone to lock it.

Bu adım için malzemeler:

Altıköşe cıvata takımıAltıköşe cıvata takımı1 centre and off-centre bolts

Gerekli aletler:

Kurbağacık anahtarKurbağacık anahtar

Malzemeler

2

Gerekli Aletler

9

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...