İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Mitre Gears: a 1:1 Bevel Pair Cut on the Milling Machine (Brown & Sharpe 1911)
Forge

Oluşturan

Forge

27. Ekim 2026NO
16
0
0
0
0

Mitre Gears: a 1:1 Bevel Pair Cut on the Milling Machine (Brown & Sharpe 1911)

Two equal bevel gears on shafts at right angles are mitre gears, and one cutter cuts both. A rotary cutter can only be right for one end of a bevel tooth, so Brown & Sharpe cut each space twice, set off centre to each side, then file the small ends round. Every figure here comes from their rules, worked out for a pair of 16 teeth, 8 pitch. Source: Brown & Sharpe, Practical Treatise on Gearing (1911), Part I ch. IX–X and Part II ch. III; set-over table p. 58. The tooth count, pitch, face width, steel and bore are ours, and so is the arithmetic. Picture: Brown & Sharpe's Fig. 24.
İleri
2 days

Talimatlar

1

Work out and turn two blanks

Ours: 16 teeth, 8 pitch, so pitch diameter 2.000 in. Mitre gears have a 45° centre angle (tangent 16/16). Diameter increment = cos 45° × working depth 0.250 = 0.177 in. Apex distance 1.414 in. Angle increment: tan = sin 45° ÷ 8, giving 5° 03′; cutting and face angle 45° − 5° 03′ = 39° 57′. Turn two blanks from steel to 2.18 in outside diameter, with the angle of edge 45° and the angle of face 39° 57′, tried with a protractor against the end of the hub. Face length ⅜ in (ours; no more than a third of the 1.414 in apex distance). Bore and hub are ours.

Bu adım için malzemeler:

Yumuşak çelik lamaYumuşak çelik lama1 length for two blanks

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
Torna kesici kalemiTorna kesici kalemi
İletkiİletki
MikrometreMikrometre
2

Choose the cutter

Back cone radius 1.414 in: twice that × 8 pitch = 22.6 teeth, so a No. 5, 8-pitch bevel gear cutter (21 to 25 teeth). One cutter does both gears. Measure its thickness Tc at the pitch line, 0.145 in (1.157 ÷ 8) from its tip.

Gerekli aletler:

Konik dişli frezesiKonik dişli frezesi
Dişli diş kumpasıDişli diş kumpası
3

Set the head and the depth

Mount the blank on the dividing head, set to the cutting angle of 39° 57′, to index 16 spaces. Set the depth at the large end to the working depth plus clearance, 0.270 in. Clearance stays the same at the small end.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
4

Set over and cut one side of every tooth

Set-over: apex distance ÷ face = 1.414 ÷ 0.375 = 3.77, so use the 3¾ column, where a No. 5 cutter has the factor .293. Set-over = Tc ÷ 2 − .293 ÷ 8 = Tc ÷ 2 − 0.037 in. Set the work off centre by that amount to one side, taking up backlash. Run the cutter through, indexing round all 16 spaces.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
5

Set over the other way and trim to thickness

Set over by the same amount on the other side of centre and rotate the blank to line the cutter up with the space at the small end. Take a trial cut, then rotate the blank toward the cutter until the tooth is right: 0.196 in thick at the large end and 0.144 in at the small end. Check both ends with the gear tooth vernier. Right at the large end but thick at the small end means too much set-over; the other way round, too little.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
Dişli diş kumpasıDişli diş kumpası
6

Cut round, then make the second gear

Cut the second side of every tooth with that setting. Cut the second blank the same way with the same cutter.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
7

File the small ends

Round the teeth over at the small ends with a file, where the cutter could not. Do not file them thinner at the pitch line.

Gerekli aletler:

İnce eğeİnce eğe

Malzemeler

1

Gerekli Aletler

9

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...