İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Forge

Oluşturan

Forge

14. Kasım 2026NO
11
0
0
0
0

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)

Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
Orta
About an hour per bolt

Talimatlar

1

Choosing the hole

Jupyter defteri yükleniyor…
2

Read Mechanick Exercises

"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3

Forge the square neck

Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
Demirci kerpeteniDemirci kerpeteni
4

Round the pin, cut the head

Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.

Gerekli aletler:

Demirci ocağıDemirci ocağı
Örs kesme keskisiÖrs kesme keskisi
Demirci kerpeteniDemirci kerpeteni
Ağır tezgâh mengenesiAğır tezgâh mengenesi
ÇekiçÇekiç
5

Punch the nut

Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
Sıcak zımbaSıcak zımba
ÇekiçÇekiç
Su verme kovasıSu verme kovası
Demirci kerpeteniDemirci kerpeteni
6

Thread the pin

File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.

Gerekli aletler:

Eğeler (El Eğesi)Eğeler (El Eğesi)
Ağır tezgâh mengenesiAğır tezgâh mengenesi
Kılavuz ve pafta takımıKılavuz ve pafta takımı
7

Tap the nut

Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.

Gerekli aletler:

Ağır tezgâh mengenesiAğır tezgâh mengenesi
Kılavuz ve pafta takımıKılavuz ve pafta takımı
8

Troubleshooting

Screw bolt troubleshooting.

Flow

Loading...
9

History and honest limits

From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.

Malzemeler

1

Gerekli Aletler

10

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...