İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)
Mark

Oluşturan

Mark

2. Kasım 2026FI
9
0
0
0
0

Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)

A scale for wagons and carts, reading the same wherever the load stands. Erastus and Thaddeus Fairbanks of St. Johnsbury, Vermont, patented it in 1831. A plank platform nine by twelve feet rests on four knife-edge hinges, one at each corner, and two levers gather the load from all four onto one rod. The rod pulls on an ordinary steelyard, which then reads only a tenth or a twentieth of the load. Result: a platform scale reading ten times (or twenty times) what the steelyard shows, the same wherever the load stands on the platform. Source: E. & T. Fairbanks, US Patent No. 118 (1837), restating their patent of 13 June 1831. Unknown: the material and sizes of the hinges, knife-edges, fulcra and levers. Picture: patent drawing.
İleri
1 week

Talimatlar

1

Build the frame

Lay two timber bed-sills, about 10 inches square and 16 feet long, parallel and about 7 feet apart. Bolt two end timbers, 8 by 14 inches and 12 feet long, across them near their ends. Just inside the end timbers, lay the two rockers, 8 inches square and 9 feet long, with their tops flush with the end timbers. Ours: carriage bolts.

Bu adım için malzemeler:

Kare kesilmiş keresteKare kesilmiş kereste6 2 sills, 2 end timbers, 2 rockers
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 takım

Gerekli aletler:

Kollu bıçkıKollu bıçkı
BurguBurgu
ÇekiçÇekiç
2

Fit the four knife-edge hinges

Bolt a hinge firmly under each end of each rocker, one at every corner of the machine. Each hinge carries two knife-edges. One rests on a fulcrum standing on the bed-sill; the other reaches out to carry the platform. Set every knife-edge parallel to the others: knife-edges at an angle cramp and bind. Not given: the material and size of the hinges, knife-edges and fulcra.

Bu adım için malzemeler:

Bilinmeyen malzemeBilinmeyen malzeme1 4 hinges, 8 knife-edges, 4 fulcra
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 takım

Gerekli aletler:

BurguBurgu
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Join the levers

Run a horizontal lever from each rocker. The longer lever reaches across nearly to the opposite rocker. The shorter one ends at a point equally far from the axes of both, and hangs there from the longer lever by a chain, rod or stirrup, so the two act as one. From the end of the longer lever a rod rises straight up to a steelyard hung from a fixed support. With the two knife-edges of each hinge 6 inches apart and the rod hung 60 inches from the lever's axis, the load is ten times the steelyard reading; at 120 inches it is twenty times. Not given: the lever material. Ours: an iron chain and a wrought iron rod.

Bu adım için malzemeler:

Bilinmeyen malzemeBilinmeyen malzeme1 2 levers
Demir zincirDemir zincir1 lever link
Dövme demir milDövme demir mil1 rod to the steelyard
Roma kantarıRoma kantarı1 adet

Gerekli aletler:

Bilinmeyen ölçülerBilinmeyen ölçüler
4

Lay the platform

Lay two timbers, short enough to pass freely between the rockers, parallel over the bed-sills. Spike stout planks 9 feet long across them, making a platform of about 9 by 12 feet. Under these timbers fasten iron plates that rest on the inner knife-edges of the hinges. Ours: nails as the spikes.

Bu adım için malzemeler:

Kare kesilmiş keresteKare kesilmiş kereste2 platform timbers
Kereste tahtasıKereste tahtası1 for 9 x 12 ft
Demir plakaDemir plaka4 adet
ÇivilerÇiviler1 as needed

Gerekli aletler:

Kollu bıçkıKollu bıçkı
ÇekiçÇekiç

Malzemeler

9

Gerekli Aletler

4

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...