İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Platinum Boat: Cut from Foil and Bent over a Brass Former (Blair, 1888)
Charlie

Oluşturan

Charlie

7. Kasım 2026DE
9
0
0
0
0

Platinum Boat: Cut from Foil and Bent over a Brass Former (Blair, 1888)

A small trough of platinum foil that carries a sample into a combustion tube. Andrew Blair (1888): "This boat is made by cutting a piece of platinum-foil in the shape shown in Fig. 65, and bending it up over a brass former into the shape shown in Fig. 64." His pattern is 3.5 long, 1.3 wide at one end and 1.07 at the other, with tabs at each end; the figure does not mark the units. Foil thickness and the former are not given. Source: A. A. Blair, The Chemical Analysis of Iron (1888), p. 129. Picture: Figs. 64-65.
Başlangıç
Unknown

Talimatlar

1

Read Blair

"This boat is made by cutting a piece of platinum-foil in the shape shown in Fig. 65, and bending it up over a brass former into the shape shown in Fig. 64."
2

Cut the blank

Cut platinum foil to the pattern of Fig. 65: 3.5 long between the end tabs, 1.3 wide at one end tapering to 1.07 at the other, with a tab .5 wide at the wide end and .37 wide at the narrow end, each flanked by V-notches. The figure does not mark the units, and the foil thickness, and how the foil is made, are not given (unknown).

Bu adım için malzemeler:

PlatinPlatin1 foil

Gerekli aletler:

Sac makasıSac makası
Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Bend it over the former

Bend the blank up over a brass former into the trough of Fig. 64, folding the end tabs up to close the ends. The shape of the former, and how it is made, are not given (ours: brass round bar as its stock).

Gerekli aletler:

Pirinç Yuvarlak ÇubukPirinç Yuvarlak Çubuk
Bilinmeyen ölçülerBilinmeyen ölçüler
4

Use

Blair opens out the sides to slide in a moist carbonaceous residue, bends them back into shape, dries the boat and contents at 100 °C, and pushes it into the porcelain or platinum tube to burn off the carbon.

Malzemeler

1
  • 1 foil
    Yer Tutucu

Gerekli Aletler

4

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...