SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing
Podolsky's variable resistor (Wirt Company, US 2,060,114, 1936). The carbon strip is bent into a ring inside a moulded casing, and instead of a sliding wiper a small roller runs round it. A coil spring presses the roller out against the strip with even pressure in every position, even over slight irregularities. The patent gives no sizes; the parts are named by what they do.
The picture: the patent's drawing (Figs. 8 and 9).
Orta
2 hours
Talimatlar
1
1
Seat the strip in the casing
Seat the strip in the casing
Bend the resistance strip into a ring against the round inner wall of the moulded casing. A small rib across the wall stops both ends of the strip so it cannot shift; the thick part at the rib has a hole for bolting the casing to a panel. Ours: flat-nose pliers to ease the strip in.
Bu adım için malzemeler:
Moulded Insulating Casing1 adet
Karbon Direnç Elemanı1 adetGerekli aletler:
Yassı Ağızlı Pense2
2
Bolt the terminals
Bolt the terminals
Put two terminal bolts through the casing wall, one at each end of the strip. Under each bolt head a small contact plate rests on the coated end of the strip.
Bu adım için malzemeler:
Terminal cıvatası2 adet
Contact Plate2 adetGerekli aletler:
Kargaburun pense3
3
Fit shaft, sleeve, collar and yoke
Fit shaft, sleeve, collar and yoke
The shaft turns in a sleeve fixed in the base of the casing. A collar on the shaft rests on the outer end of the sleeve; on the inner end the shaft carries a yoke, with a spring washer between yoke and sleeve so the shaft cannot slide. Ours: pliers to seat the spring washer.
Bu adım için malzemeler:
Kontrol mili1 adet
Shaft Sleeve1 adet
Shaft Collar1 adet
Shaft Yoke1 adet
Spring Washer1 adetGerekli aletler:
Kargaburun pense4
4
Fit the sprung roller
Fit the sprung roller
The yoke's slotted ends guide a flat stem. The roller sits in the stem's forked outer end. A washer on shoulders of the stem, pushed out by a coil spring, holds the roller on the strip with even pressure all the way round.
Bu adım için malzemeler:
Roller Stem1 adet
Contact Roller1 adet
Düz Pul1 adet
Coil Spring1 adetGerekli aletler:
Kargaburun penseMalzemeler
13- Yer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
2- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


