İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)
Forge

Oluşturan

Forge

4. Kasım 2026NO
15
0
0
0
0

Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)

An air furnace melts iron apart from the fuel: coal burns on a grate at one end, and the flame is thrown down from a low arched roof onto the iron on the bed, then leaves by a tall chimney. The iron stays cleaner than in a cupola, so founders used it for guns, rolls, heavy scrap and lumps too big for the cupola. This furnace is 30 ft 6 in long and 7 ft wide outside, 5 ft wide inside, cased in bolted wrought-iron plates. Source: S. Bolland, The Iron Founder Supplement (1893), pp. 55-67. Unknown: brick sizes, plate thickness. Picture: Fig. 14 of the book.
Uzman
Unknown

Talimatlar

1

Lay the foundation

Build the foundation solid of common material up to the firebrick, shaped so the firebrick bed slopes down from the chimney end to the reservoir. Keep the bricks from B to C 6 in below the finished bottom, to leave room for the sand bed.

Bu adım için malzemeler:

TuğlaTuğla1 foundation

Gerekli aletler:

MalaMala
Bilinmeyen ölçülerBilinmeyen ölçüler
2

Build the fireplace, bridge and roof

Build the fireplace the full width of the furnace (5 ft inside, grate 5 ft long). Set the bridge wall at least 2 ft 3 in from the face of the grate bars. Build bridge, sides, roof and fireplace of the most refractory firebrick. Arch the roof the whole length, low, so it throws the flame down onto the bed; fill above the arches with common material. Leave the side charging hole (5 x 4 ft), the top hole (furnace width x 6 ft), the puddling hole over the reservoir, a sight hole and the tap hole.

Bu adım için malzemeler:

Ateş tuğlasıAteş tuğlası1 lining, bridge, roof
Refrakter kil harcıRefrakter kil harcı1 setting
TuğlaTuğla1 filling above the arch
Bilinmeyen metalBilinmeyen metal1 grate bars

Gerekli aletler:

MalaMala
3

Case it in plates and bolt it

Case the whole structure in wrought-iron plates, held at the corners with angle-irons. Run eight chief anchor bolts from side to side, clear of all working parts. Join everything with bolts, not rivets, so any plate can come off for repairs. Line the charging doors with firebrick.

Bu adım için malzemeler:

Demir plakaDemir plaka1 casing, doors
Dövme demir milDövme demir mil8 anchor bolts
Bilinmeyen metalBilinmeyen metal1 angle-irons, door frames
Ateş tuğlasıAteş tuğlası1 door linings

Gerekli aletler:

Bilinmeyen ölçülerBilinmeyen ölçüler
4

Build the chimney

Build the chimney square, 30 to 40 ft high, with an inside course of firebrick (Fig. 14: 2 ft 6 in square inside). Make its area a little larger than the fireplace. Put a damper on top that can be worked from the bottom: it alone sets the draught. It can stand apart on a sole plate on four columns.

Bu adım için malzemeler:

Ateş tuğlasıAteş tuğlası1 inside course
TuğlaTuğla1 chimney
Bilinmeyen metalBilinmeyen metal1 damper

Gerekli aletler:

MalaMala
5

Make the sand bottom

Make the bottom from B round the reservoir to C with 8 parts fire-sand to 1 of clay and 1 of ground coke. Fire it well for one to two hours before the first charge; it should last ten heats. Fill the tap hole with fire-sand and a little coal dust, which will not cake when hot.

Bu adım için malzemeler:

KumKum8 parts
KilKil1 part
Metalurjik kokMetalurjik kok1 part, ground

Gerekli aletler:

Taş kömürüTaş kömürü
6

Charge and melt

Fire with soft, non-caking bituminous coal and keep a full grate; clinker quickly and leave no holes for cold air. Charge all the iron at the start: first layer of pigs lengthwise and a little apart, next layers across, open so the flame passes. Set heavy pieces on firebricks so the flame plays all round them. Through the puddling hole, dip test pieces and skim the iron clean. To blend two grades, thrust green saplings into the melt. Close the damper before tapping. Look the furnace over after every heat.

Gerekli aletler:

Taş kömürüTaş kömürü
Pik demir külçeleriPik demir külçeleri
Sert Ağaç FidanıSert Ağaç Fidanı
Delikli kevgirDelikli kevgir

Malzemeler

9

Gerekli Aletler

6

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...