İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
Henry Rohrer of Strasburg township, Pennsylvania, received US 26,377, dated 6 December 1859, for improvements to the common barrel churn, which he named the "Champion atmospheric churn". Four concave, tapering dashers run close to the staves with their wide and narrow ends alternating, so they rub as well as beat. Two tubes through the rear head let fresh air into the middle and steam and musty air out; in winter a funnel-mouthed pipe set near a hot stove brings warm air instead.
The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing
Talimatlar
1
1
Rohrer's temperatures, and the dashers' sweep
Rohrer's temperatures, and the dashers' sweep
Jupyter defteri yükleniyor…
2
2
Air into the cream, three weeks before
Air into the cream, three weeks before
Clow pumped air in at the bottom. Rohrer lets it in by pipes alone, warmed from the stove when needed.
3
3
Read US 26,377
Read US 26,377
"The concaved, tapering sides of the dashers with the wide end of the one followed by the narrow end of the other in its revolutions, produces side eddies as well as being beaten and partially retained by the concaved side; thus a thorough mixing is produced, while a constant supply of fresh air is admitted through the pipe G to the center of the churn"
4
4
Print the step F
Print the step F
A raised open step 80 x 80 mm and 55 mm deep, open at the sides, with a 17 mm socket for the rear pivot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Barrel A, base B and hatch
Barrel A, base B and hatch
Use a wooden barrel about 450 mm long inside, 320 mm across at the heads. Cut a 120 mm hatch in the bilge with a hardwood lid. Bore the front head 17 mm in its centre for the shaft. Bore the rear head 21 mm in its centre for tube K and 21 mm 120 mm above it for tube I. Make a cradle of two shaped hardwood saddles on a base board so the barrel lies level. Fill the barrel with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Ahşap fıçı1 adet
Sert Ağaç Tahtası2 adet
Ahşap Tutkalı1 adet
Ahşap vidalar12 adetGerekli aletler:
Dekupaj Testere
Pusula
Kablosuz Matkap
Yassı matkap ucu takımı
Daire testere tezgâhı
Çubuklu işkence
Şerit Metre
Su6
6
Dashers D and crosses E
Dashers D and crosses E
Shave four hardwood dashers 400 mm long, tapering from 70 to 35 mm wide, with a 20 mm deep concave face on the inner side and the outer edge left straight. Make two crosses of hardwood 15 x 24 mm, 290 mm across, and screw the dashers to their ends, outer edges 150 mm from the centre, the wide ends alternately at the front and the rear. Fix the front cross on a 16 mm stainless shaft through the front head with a crank C outside, and a 16 mm pivot on the rear cross's centre.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Ahşap vidalar16 adet
Paslanmaz çelik çubuk1 adet
Shaft Collar2 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adetGerekli aletler:
Çift saplı rende
Daire testere tezgâhı
Kablosuz Matkap
Matkap Ucu Takımı
Demir Testeresi
Eğeler (El Eğesi)
Tornavida takımı
Zımpara Kağıdı
Şerit Metre7
7
Step F, tubes I and K, pipes G and H
Step F, tubes I and K, pipes G and H
Screw the printed step over the rear head's centre hole, its socket on the axis. Seal two 20 mm stainless tubes, 70 mm long, through the rear head: K in the centre under the step, I above it. Make the atmospheric pipe G: an upright stainless tube open at its top, joined to I and K by short tubes and elbows. For winter make pipe H: a stainless funnel, mouth m, on a tube to K, with a tee on the tube from I open as the vent l; set the funnel near a warm stove, never on it, and use silicone tube for the joints.
Bu adım için malzemeler:
Paslanmaz çelik boru2 adet
Paslanmaz çelik huni1 adet
Ahşap vidalar4 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Demir Testeresi
Eğeler (El Eğesi)
Propan Pürmüz
Tezgah Mengenesi
Isıya Dayanıklı Eldiven
Tornavida takımı8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the barrel, heads and cradle cut through the middle: the four alternately reversed dashers on their two crosses, the shaft and crank, the step F on the rear head over tube K, tube I, and the atmospheric pipe G outside. The frame was turned through a quarter turn.
9
9
Churn
Churn
Fill the barrel about half full with heavy cream, about 15 litres. Bring it to 15-18 °C, checked with the thermometer; in winter put pipe H on with its funnel near the warm stove, otherwise pipe G. Close the hatch and turn the crank steadily, timing it. When the butter comes, open the hatch, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema15 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi10
10
Troubleshooting
Troubleshooting
Atmospheric barrel churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Henry Rohrer** of Strasburg township, Lancaster County, Pennsylvania, US 26,377, 6 December 1859, "Churn". He knew of other ways of bringing air to cream, and claimed the tubes I, K in the rear head with the pipes G and H, mouth m, partition l and tubes L, M, with the dashers D on an open step F. He says he "tested in my own buttery to my entire satisfaction". The patent gives no sizes; every size here is ours. His temperatures, 60 to 65 °F, are 15.6 to 18.3 °C.
Malzemeler
15- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 32 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 15 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
22- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
2Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
Buttercup tarafından
YİYECEK & İÇECEK
5
0
0
0
0
0

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
Buttercup tarafından
Ağaç işleri
13
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

