İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Tooled Calfskin Coin Purse: Lined, Flap Over Front, Design Split Between Flap and Front (Boy Mechanic, 1915)
Tex

Oluşturan

Tex

13. Kasım 2026FO
7
0
0
0
0

Tooled Calfskin Coin Purse: Lined, Flap Over Front, Design Split Between Flap and Front (Boy Mechanic, 1915)

The first piece in Mary C. Scovel's leather course (The Boy Mechanic, Book 2, 1915): a coin purse of Russian calfskin from a 4 by 8 in piece, its design traced, lined and tooled or stamped, split so half sits on the flap and half on the front below it, then lined with silk and stitched.
Başlangıç
About 3 hours

Talimatlar

1

Her sizes in centimetres

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

Her outfit: "two special tools costing 50 cents each, one with a narrow edge for lining patterns, and one with broad ends for tooling; and a piece of tin, plate glass, or very smooth hard wood, which should not be smaller than 9 by 12 in. A soft sponge, a triangle, a rule, tracing paper and a hard pencil are also needed." Russian calfskin is best for tooling and stamping.
3

Make the paper pattern

The purse has three parts: front, back and flap. Fold paper to the proportions you want, with the design for the front D on the same side of the paper as the flap C; the space F under the flap has no design. Fold F behind H, then C behind H and F, and turn the pattern over to see the purse. Cut a piece of leather 4 by 8 in, which leaves 1/4 in outside the pattern for pinning.

Bu adım için malzemeler:

Dana derisiDana derisi1 adet

Gerekli aletler:

Aydınger kâğıdıAydınger kâğıdı
Kurşun kalemKurşun kalem
MakasMakas
CetvelCetvel
4

Damp the leather and transfer the design

Draw the whole design for the purse on tracing paper. Wet the leather on the wrong (unfinished) side with a soft sponge: pat it to moisten, not soak, it; too wet and the tool sticks and leaves an uneven background. Pin the design firmly on the leather, tack the leather down on its outer margin to the glass or board, and go over every line with a hard pencil, with firm, even pressure. Lift the paper and go over the lines with the narrow lining tool, with a strong, firm stroke. A line design can stop here.

Bu adım için malzemeler:

Dana derisiDana derisi1 adet

Gerekli aletler:

SüngerSünger
Aydınger kâğıdıAydınger kâğıdı
Kurşun kalemKurşun kalem
Raptiye (50'lik kutu)Raptiye (50'lik kutu)
Cam levhaCam levha
Deri modelleme aletiDeri modelleme aleti
5

Tool or stamp the background

Leave at least 1/8 in between the edge of the pattern and the design. To tool, press the background down with the broad end in even, long strokes; if it will not go down, the leather is too dry, so take it off and damp the back again. Keep the edges sharp between pressed and raised parts. To stamp instead, strike a small carpenter's nail set lightly with a wooden mallet in rows of circles; too hard a blow cuts the leather.

Gerekli aletler:

Deri modelleme aletiDeri modelleme aleti
Çivi gömme zımbasıÇivi gömme zımbası
Ahşap TokmakAhşap Tokmak
SüngerSünger
6

Line and stitch

Fold the parts together, line with silk to match the leather, and stitch the front and back parts close to the edge. Stitch on a sewing machine with a long stitch, a large needle and silk as heavy as the needle takes; try it on a scrap first, and put tissue paper over the leather if the foot marks it. Without a machine, prick holes with an awl and sew with needle and silk, running or over-and-over; going over-and-over to the end and back gives an X stitch. She has the catch M put on by a shoemaker or trunk store; a snap fastener is used here.

Bu adım için malzemeler:

İpek Kumaşİpek Kumaş1 adet
İpek iplikİpek iplik1 adet
Buğday tutkalıBuğday tutkalı1 adet
ÇıtçıtÇıtçıt1 adet

Gerekli aletler:

MakasMakas
Dikiş makinesiDikiş makinesi
BizBiz
İki saraç iğnesiİki saraç iğnesi
7

Troubleshooting

Tooled leather troubleshooting.

Flow

Loading...
8

History and honest limits

From Mary C. Scovel, "Arts-Crafts Leather Work", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 432-441), Part I. She gives the piece size but no finished purse size; the shape comes from her pattern. The snap fastener, tools and metric figures are ours.

Malzemeler

5

Gerekli Aletler

13

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...