İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

Oluşturan

Forge

26. Ekim 2026NO
26
0
0
0
0

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
Başlangıç
30 minutes

Talimatlar

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

Bu adım için malzemeler:

Demir telDemir tel1 adet

Gerekli aletler:

CetvelCetvel
Yan keskiYan keski
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

Gerekli aletler:

İğne Eğe Takımıİğne Eğe Takımı
Tezgah MengenesiTezgah Mengenesi
3

Point the screw end

File that end to a tapering point (Fig. 3).

Gerekli aletler:

Metal EğeMetal Eğe
Tezgah MengenesiTezgah Mengenesi
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

Gerekli aletler:

Pafta koluPafta kolu
Tezgah MengenesiTezgah Mengenesi
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

Gerekli aletler:

Yuvarlak uçlu penseYuvarlak uçlu pense
Yassı Ağızlı PenseYassı Ağızlı Pense
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

Bu adım için malzemeler:

Demir telDemir tel1 adet

Gerekli aletler:

Yan keskiYan keski
Yuvarlak uçlu penseYuvarlak uçlu pense
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

Gerekli aletler:

Yassı Ağızlı PenseYassı Ağızlı Pense
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

Malzemeler

1

Gerekli Aletler

8

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...