İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
Charlie

Oluşturan

Charlie

9. Kasım 2026DE
15
0
0
0
0

Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)

A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock. The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap. Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
İleri
Unknown

Talimatlar

1

Read Demers

"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2

Blow the vessel

Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.

Bu adım için malzemeler:

Bilinmeyen camBilinmeyen cam1 vessel

Gerekli aletler:

Tezgâh üstü cam üfleme şalomasıTezgâh üstü cam üfleme şaloması
Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Fuse on the stopcock

Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).

Bu adım için malzemeler:

Cam muslukCam musluk1 plug of glass or PTFE

Gerekli aletler:

Tezgâh üstü cam üfleme şalomasıTezgâh üstü cam üfleme şaloması
Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
4

Make the plastic stem

Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.

Bu adım için malzemeler:

Bilinmeyen malzemeBilinmeyen malzeme1 flexible plastic stem
O-ring contaO-ring conta1 adet

Gerekli aletler:

Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
Bilinmeyen ölçülerBilinmeyen ölçüler
5

Assemble and use

Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.

Malzemeler

4

Gerekli Aletler

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...