İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
Forge

Oluşturan

Forge

13. Kasım 2026NO
11
0
0
0
0

Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)

Albert G. Sewell received US 1,674,999, dated 26 June 1928, for a soft-face hammer whose worn faces can be renewed instead of throwing the hammer away. Each end of the head is a cup. A face rolled from a strip is pressed into the cup onto a loose sheet-metal disc whose prongs bite into it and wedge it tight. When a face is battered, a rod pushed through a notch at the bottom of the cup drives the disc and the face out together, and a new face goes in. He preferred rawhide and named rubber among face materials; ours are rolled from rubber sheet. The patent gives no sizes; every size here is ours.
Orta
About 1 day

Talimatlar

1

Rolling a face plug

Jupyter defteri yükleniyor…
2

Read US 1,674,999

"Thus, by hammering or otherwise thrusting a rod or suitable device against the wedging member, the latter, with the striking face member, can be forced or driven out of the socket or recess, after which a new striking face member may be forced into the socket, to be secured therein by the wedging member."
3

Turn the head

Grip 40 mm steel round bar in the chuck and turn a head 110 mm long: the two ends stay 40 mm across for 26 mm as the flanges D, and the middle is waisted to 30 mm. Bore each end 32 mm across and 22 mm deep for the sockets C, flat at the bottom. Drill a 20 mm eye B through the middle, square to the axis, in a V-block on the drill press.

Bu adım için malzemeler:

Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk1 adet
Kesme yağıKesme yağı1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Delik işleme kateriDelik işleme kateri
Kesme kalemiKesme kalemi
Sütunlu MatkapSütunlu Matkap
V BlokV Blok
Matkap Ucu TakımıMatkap Ucu Takımı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Koruyucu gözlükKoruyucu gözlük
4

Cut the notches K

On the handle's side of each flange, saw and file a notch 8 mm wide through the flange's wall at the very bottom of the socket, so a rod can be pushed in at a slant against the edge of the disc at the bottom.

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Demir TesteresiDemir Testeresi
Eğe TakımıEğe Takımı
Nokta ZımbasıNokta Zımbası
5

Pronged discs G

Cut two discs of 1.5 mm steel sheet 31.5 mm across. At four places round each rim, snip two cuts 6 mm deep 5 mm apart and bend the tab between them up at a right angle with the pliers: the prongs H. Drop one disc loosely into the bottom of each socket, prongs out.

Bu adım için malzemeler:

Yumuşak Çelik SacYumuşak Çelik Sac1 adet

Gerekli aletler:

Sac makasıSac makası
Yassı Ağızlı PenseYassı Ağızlı Pense
Tezgah MengenesiTezgah Mengenesi
Eğe TakımıEğe Takımı
6

Roll and press in the faces E

Cut two strips of 3 mm natural rubber sheet 32 mm wide and about 270 mm long. Roll each tightly into a coil, trimming the strip until the coil just enters a socket, and tie it. Press the coil into its socket in the vice, between soft packing, until it bottoms on the disc and its prongs bite in, leaving the face standing about 10 mm out. Cut the tie and trim the face flat with the knife.

Bu adım için malzemeler:

Doğal kauçuk levhaDoğal kauçuk levha1 adet

Gerekli aletler:

Maket BıçağıMaket Bıçağı
Tezgah MengenesiTezgah Mengenesi
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
7

Handle

Turn an ash handle 300 mm long, its end a tight fit in the eye. Saw a slot down its end, drive it into the eye, and glue and drive a hardwood wedge into the slot; saw it off flush.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
Torna kalemi seti (HSS)Torna kalemi seti (HSS)
Demir TesteresiDemir Testeresi
Küre başlı çekiçKüre başlı çekiç
8

Renew a face

When a face is worn, push a steel rod through the socket's notch against the disc's edge and tap it out with the hammer; the disc and the face come out together. Put the disc back, prongs out, and press in a new rolled face.

Gerekli aletler:

Küre başlı çekiçKüre başlı çekiç
Tezgah MengenesiTezgah Mengenesi
9

Troubleshooting

Soft-face hammer troubleshooting.

Flow

Loading...
10

History and honest limits

**Albert G. Sewell**, US 1,674,999, dated 26 June 1928, filed 25 July 1927. He describes a head with a socket at each end formed by annular flanges, a striking face member of relatively soft material rolled from a strip and pressed in as a plug, a loose sheet-metal wedging disc with prongs in the socket's bottom, and openings through which a rod drives the disc and face out. He preferred rawhide and his head was cast iron; ours is turned steel with faces rolled from rubber sheet, which he lists among the face materials in use. He gives no sizes; every size here is ours.

Malzemeler

6

Gerekli Aletler

20

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...