SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Using Relays — SIK Circuit 13
Ed

Oluşturan

Ed

17. Mart 2026FI
79
0
0
0
0

Using Relays — SIK Circuit 13

Control a relay with a transistor to switch between two LEDs. Learn about electromechanical switching, SPDT relays, Normally Open vs Normally Closed contacts, and flyback protection.

Talimatlar

1

Parts & Introduction

A relay is an electrically-operated mechanical switch. A small current energizes a coil that physically moves a contact arm, switching a separate circuit. Relays can control high-power devices (motors, lights, appliances) from low-power Arduino signals. This experiment uses an SPDT (Single Pole Double Throw) relay to alternate between two LEDs.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x SPDT Relay
  • 1x NPN Transistor (P2N2222A)
  • 1x Diode (1N4148)
  • 2x LEDs (different colors)
  • 2x 330Ω Resistors
  • 14x Jumper Wires

Bu adım için malzemeler:

SparkFun Inventors Kit - V3.2SparkFun Inventors Kit - V3.21 kit
Arduino Uno R31 adet
Breadboard1 adet
SPDT Relay1 adet
NPN Transistor (P2N2222A)1 adet
Diode (1N4148)1 adet
5mm LED1 adet
330 Ohm Resistor330 Ohm Resistor2 adet
Jumper WiresJumper Wires8 adet

Gerekli aletler:

Computer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

Transistor + Relay Coil
  1. Connect transistor Base through 330Ω resistor to Arduino Digital Pin 2.
  2. Connect transistor Emitter to GND.
  3. Connect one side of the relay coil to transistor Collector.
  4. Connect other side of relay coil to 5V.
  5. Flyback Diode: Band (cathode) to 5V, anode to Collector.
Relay Contacts + LEDs
  1. Connect relay COMMON through a 330Ω resistor to 5V.
  2. Connect relay NC (Normally Closed) to LED 1 positive leg.
  3. Connect relay NO (Normally Open) to LED 2 positive leg.
  4. Connect both LED negative legs to GND.

Bu adım için malzemeler:

SPDT Relay1 adet
NPN Transistor (P2N2222A)1 adet
Diode (1N4148)1 adet
5mm LED1 adet
330 Ohm Resistor330 Ohm Resistor2 adet
Breadboard1 adet
Jumper WiresJumper Wires8 adet
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

relay.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 13 — RELAYS

Use a transistor to drive a relay, alternating two LEDs.

Hardware connections:
  Transistor BASE through 330 ohm resistor to digital pin 2
  Transistor EMITTER to GND
  Relay coil: one side to COLLECTOR, other to 5V
  Flyback diode: band to 5V, anode to COLLECTOR
  Relay COMMON through 330 ohm to 5V
  Relay NC to LED 1 positive, Relay NO to LED 2 positive
  Both LED negatives to GND

This code is completely free for any use.
*/

const int relayPin = 2;
const int timeDelay = 1000;

void setup()
{
  pinMode(relayPin, OUTPUT);
}

void loop()
{
  digitalWrite(relayPin, HIGH);  // Relay on (COM connects to NO)
  delay(timeDelay);

  digitalWrite(relayPin, LOW);   // Relay off (COM connects to NC)
  delay(timeDelay);
}

Bu adım için malzemeler:

Arduino Uno R31 adet

Gerekli aletler:

Computer with Arduino IDE
4

Test & Experiment

What You Should See

You should hear the relay clicking, and see the two LEDs alternating — one on, one off — switching every second.

Troubleshooting

  • LEDs not lighting: Check LED polarity — longer leg is positive.
  • No clicking sound: The transistor or coil circuit isn't working. Verify transistor orientation and coil connections.
  • Relay not making good contact: The SIK relay is designed for soldering, not breadboarding. Press it firmly to ensure all pins contact.
  • Confusion: Don't mix up the TMP36 temperature sensor with the transistor!

Experiments to Try

  • Replace the LEDs with a motor on the NO contact — use the relay as a motor on/off switch.
  • Use a button to control when the relay toggles.
  • Add variable delay to create morse code patterns.

Malzemeler

9

Gerekli Aletler

1
  • 13
    Computer with Arduino IDE
Tahmini toplam
$181.00

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...