İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)
Ed

Oluşturan

Ed

4. Kasım 2026FI
11
0
0
0
0

Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)

A breadboard lets you build a circuit without solder: push component leads into holes and spring contacts underneath join them in rows. John N. Tengler of A P Products received US 4,420,215 (1983) for one: a one-piece moulded acetal housing with holes on 0.100 in centres, and sets of three springy cantilever contacts of copper alloy No. 688 pushed in from below. Not given: the contact thickness and sizes, how the contacts are formed, and the moulding conditions. Source: J. N. Tengler, US 4,420,215. Picture: the patent's drawing sheet.
İleri
Not given in the source

Talimatlar

1

Mould the housing

Injection-mould the housing as one piece in acetal copolymer (Tengler names CELCON). His example has 78 cells in 26 rows of three, open at the bottom, under a top wall whose holes sit on 0.100 in centres. Give each cell two preload bars on its front wall, one either side of the hole, with tapered lower ends. Mould notches into the walls between the cells of a row, and none into the front and back walls, so a contact set fits only the right way round.

Bu adım için malzemeler:

Asetal kopolimer granülleriAsetal kopolimer granülleri1 one housing

Gerekli aletler:

Enjeksiyon kalıplama makinesiEnjeksiyon kalıplama makinesi
Enjeksiyon kalıp çerçevesiEnjeksiyon kalıp çerçevesi
Bilinmeyen ölçülerBilinmeyen ölçüler
2

Form the contact sets

Form three identical contacts from copper alloy No. 688, joined at the foot by a strip. Each is a single cantilever: a foot with a seat, an arm curving up into a spring, a hairpin bend, then a contact face that a pushed-in lead slides along, ending in a tip, with a stop extension that comes to rest against the arm. If you like, stamp a small barb in the joining strip.

Bu adım için malzemeler:

688 bakır alaşımı şerit688 bakır alaşımı şerit1 one set of three per row

Gerekli aletler:

Bilinmeyen şekillendirme yöntemiBilinmeyen şekillendirme yöntemi
Bilinmeyen ölçülerBilinmeyen ölçüler
3

Push the sets in from below

Push each set up into its row from the open bottom, contact faces toward the holes, with the strip running through the notches. The strip is bent at a slight angle, so the front wall springs it and wedges the contact's foot against the back wall. The preload bars press on the contact face, and the barb, if there is one, bites into the plastic.

Gerekli aletler:

Yassı Ağızlı PenseYassı Ağızlı Pense
4

Check a row

Push a resistor lead through a hole: it should slide along the contact face. The two end contacts of a row join two components; Tengler meant the middle one for injecting or testing a signal. Check with a meter that the three holes of a row connect and neighbouring rows do not.

Gerekli aletler:

DirençDirenç
MultimetreMultimetre

Malzemeler

2

Gerekli Aletler

7

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...