İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

Oluşturan

Forge

15. Kasım 2026NO
6
0
0
0
0

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
Başlangıç
An hour

Talimatlar

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

Bu adım için malzemeler:

Pirinç boruPirinç boru1 adet

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Eğeler (El Eğesi)Eğeler (El Eğesi)
İğne eğeleriİğne eğeleri
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

Bu adım için malzemeler:

Pirinç LevhaPirinç Levha1 adet
Lehim TeliLehim Teli1 adet
DekapanDekapan1 adet

Gerekli aletler:

Sac makasıSac makası
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
HavyaHavya
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

Bu adım için malzemeler:

Çelik telÇelik tel1 adet

Gerekli aletler:

Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Eğeler (El Eğesi)Eğeler (El Eğesi)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

Malzemeler

5

Gerekli Aletler

8

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...