İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Oblique Perforated-Dasher Churn: A Slanted Spindle Drives the Cream Down and Sideways, a Guard Turns It Back
E. N. Sprinkle of Marion, Virginia, received US 25,985, dated 1 November 1859, for a churn. Three perforated dashers turn on a spindle set slantwise across the churn, from a standard low on one side to a slot in the rim on the other, and a crank on its end turns it fast. The cream is driven down and towards one side and cut by the holes' edges; a sloping guard under the dashers sends it back up to them, and the bottom stays clear for gathering the butter.
The patent gives no sizes; every size here is ours.
Başlangıç
About a day, plus printing
Talimatlar
1
1
The spindle's slope, and where the cream goes
The spindle's slope, and where the cream goes
Jupyter defteri yükleniyor…
2
2
A turning dasher with curved wings, seven weeks before
A turning dasher with curved wings, seven weeks before
Hassler's dasher stands upright. Sprinkle tilts his spindle so the dashers drive the cream sideways too.
3
3
Read US 25,985
Read US 25,985
"By reason of the dashers being operated in an oblique position, it will be seen that the cream will not only be forced down but will also be forced toward the side of the churn which supports the upper end of the dasher shaft, and is thus not only effectually agitated by the motion of the dashers, but is also cut and stirred by the edges of the perforations c, c, c, in the dashers"
4
4
Print the dashers C
Print the dashers C
Three perforated half-ellipse blades, 210 x 80 mm and 4 mm thick, round a 24 mm tube bored 12.6 mm, with a cross hole for a pin. Print with supports. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the standard f
Print the standard f
A post 30 mm square and 178 mm tall on a 60 mm base with an M6 nut trap, its top bored 12.8 mm at 38 degrees for the spindle's lower end, e. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the guard's leg
Print the guard's leg
A leg 24 mm across and 92 mm tall on a 50 mm foot, to hold the guard's low end. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Standard f, guard F and slot h
Standard f, guard F and slot h
Drill a 6.5 mm hole in the bucket's floor 115 mm from its centre. Push an M6 nut into the standard's trap, lay an O-ring under its base and bolt it over the hole from underneath, its sloping bore facing across the bucket. Cut the guard F from 8 mm hardwood: a half-circle to fit the bucket 110 mm up, notched round the standard. Screw it to the standard's side 125 mm up and onto its leg, 95 mm up at the far end, on one side of the spindle's line. Cut a slot 13 mm wide and 12 mm deep in the rim opposite the standard, and screw an eye h' beside it.
Bu adım için malzemeler:
20 Litrelik Kova1 adet
Altıköşe cıvata takımı1 adet
Altıgen Somun1 adet
Düz Pul1 adet
O-ring conta1 adet
Sert Ağaç Tahtası1 adet
Ahşap vidalar4 adet
Kopça1 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Kablosuz Matkap
Matkap Ucu Takımı
Dekupaj Testere
Pusula
Demir Testeresi
Eğeler (El Eğesi)
Kurbağacık anahtar
Tornavida takımı8
8
Spindle D and crank E
Spindle D and crank E
Cut 12 mm stainless rod 625 mm long. Heat 415 mm from one end with the torch and bend it at right angles, then 120 mm further on bend it back parallel to make the crank. Slide the dasher onto the straight part and pin it 70 mm from the end. Set the end into the standard's bore and lay the spindle in the slot, then hook the catch g over it into the eye.
Bu adım için malzemeler:
Paslanmaz çelik çubuk1 adetGerekli aletler:
Propan Pürmüz
Tezgah Mengenesi
Çekiç
Isıya Dayanıklı Eldiven
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı9
9
Cover B
Cover B
Cut a hardwood cover to sit on the rim, with a notch for the spindle at the slot, a 10 mm vent hole j, and a screw eye in the middle with a ring of stainless wire for lifting, i.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Halkalı vida1 adet
Paslanmaz çelik tel1 adetGerekli aletler:
Dekupaj Testere
Pusula
Kablosuz Matkap
Matkap Ucu Takımı
Zımpara Kağıdı10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket and cover cut through the middle: the standard, the slanting spindle with its crank, the three-bladed dasher, and the guard on its leg. The dasher was turned through 24 angles.
11
11
Churn
Churn
Pour about 6 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the cover on. Turn the crank fast and steadily, timing it. When the butter comes, unhook the catch, lift the spindle and dasher out, gather the butter from the clear bottom, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema6 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi12
12
Troubleshooting
Troubleshooting
Oblique dasher churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**E. N. Sprinkle** of Marion, Smyth County, Virginia, US 25,985, 1 November 1859, "Churn". He claimed, as an improvement on the churn patented to Hatfield and Goldsmith on 13 July 1858, "the combination of the perforated obliquely arranged dashers C, C, C, with the single inclined stationary guard F". The patent gives no sizes; every size here is ours. His cover is conical; ours is flat.
Malzemeler
15- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 6 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
18- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
4Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Hinged-Leaf Wing Dasher Churn: Turn One Way to Churn, Reverse and a Leaf Opens to Gather the Butter
Buttercup tarafından
Ağaç işleri
7
0
0
0
0
0

Hooked Breaker-Frame Churn: Breakers Held Still From the Lid, Then Hooked to the Dasher to Gather
Buttercup tarafından
YİYECEK & İÇECEK
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

