İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Frank A. Stanley · Public domain (1919)
Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)
Die makers made their own dowel pins two at a time: one piece of steel is turned, necked in the middle, hardened, ground dead straight to size from each end, then snapped in two at the neck. Frank Stanley described the practice of one die shop.
Source: F. A. Stanley, Punches and Dies (1919), pp. 417–419. The choice of tool steel and the forge for hardening are ours; the passage gives no hardening heat. Picture: Stanley's Fig. 610, grinding dowel pins.
Orta
1 day
Talimatlar
1
1
Cut stock for two pins
Cut stock for two pins
Take a length of steel a little larger than the dowel size and long enough for two pins. It must harden, so use tool steel (our choice).
Bu adım için malzemeler:
Sekizgen takım çeliği çubuk1 length for two pinsGerekli aletler:
Tezgah Mengenesi2
2
Turn 0.008 in over size
Turn 0.008 in over size
Turn it on centres to about 0.008 in above the finished size.
Gerekli aletler:
Metal Torna Tezgâhı
Torna kelepçesi
Mikrometre3
3
Neck it in the middle
Neck it in the middle
Cut a neck 1/16 in deep in the middle, the dividing line between the two pins.
Gerekli aletler:
Metal Torna Tezgâhı4
4
Harden
Harden
Harden the piece. This passage gives no heat; heat to hardening heat and quench in the usual way for your steel (ours).
Gerekli aletler:
Demirci ocağı
Maşa
Su verme kovası5
5
Grind each half to size
Grind each half to size
Put it on dead centres in the grinding machine and grind the diameter to size from one end to the neck. Reverse it on the centres and grind from the other end. The pins come out perfectly straight from end to end.
Gerekli aletler:
Silindirik taşlama tezgâhı
Torna kelepçesi
Mikrometre6
6
Break the pins apart
Break the pins apart
Break the piece apart at the neck. You have two dowel pins ground closely to standard size; ream their holes true and straight to fit.
Gerekli aletler:
Tezgah MengenesiMalzemeler
1- 1 length for two pinsYer Tutucu
Gerekli Aletler
8- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
