İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
Buttercup

Oluşturan

Buttercup

11. Kasım 2026IE
11
0
0
0
0

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher

James Taylor of Rushville, Illinois, received US 25,453, dated 13 September 1859, for a churn. An upright dasher of horizontal bars, flattened out towards their ends, turns in a wooden tub and sets the cream turning. Upright brakes inside the tub break the current, and slots in them next to the wall let part of it run on to narrower ledges, which turn it back towards the dasher. The patent gives no sizes; every size here is ours.
Orta
About 2 days

Talimatlar

1

Bars, brakes and how much cream

Jupyter defteri yükleniyor…
2

Breakers round a turning dasher, a few weeks before

Sperry's breakers stood on a frame. Taylor fixes his to the tub's wall and slots them next to it.
3

Read US 25,453

"by the action of the dasher the mass of cream or milk in the tub is caused to assume a rotary motion, and the current thus created by coming in contact with the brakes, c, is thrown violently against the sides of the tub and as it passes through the openings, e, in the back part of these brakes and along the sides of the tub, it (the current) strikes against the ledges, d, whereby it is turned in again, toward the dasher"
4

Tub A and cover B

Use a wooden tub 260 mm across inside at the bottom, 230 mm at the top and 420 mm deep, with its top hoop driven up to stand 25 mm above the staves. Glue a hardwood step, 70 mm across and 22 mm thick with a 27 mm hole 16 mm deep, in the middle of the floor. Cut a round cover to drop inside the top hoop, saw it in two across the middle, and bore a 42 mm hole in the middle and a 20 mm air hole 80 mm off it.

Bu adım için malzemeler:

Ahşap tekneAhşap tekne1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Ahşap TokmakAhşap Tokmak
Şerit MetreŞerit Metre
5

Brakes c and ledges d

From 12 mm hardwood cut three brakes 30 mm wide and three ledges 18 mm wide, 345 mm long, their outer edges planed to the staves' slope. In each brake cut a slot 10 mm wide next to its outer edge, stopping 40 mm from each end: the openings e. Screw the brakes upright to the staves through the wall, 15 mm above the floor, one every third of the way round. Screw a ledge 15 degrees after each brake, in the way the dasher turns.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap vidalarAhşap vidalar18 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
Zımpara KağıdıZımpara Kağıdı
6

Dasher D and its crank

Turn a hardwood shaft C 40 mm across and 503 mm long, its foot turned to 25 mm for 15 mm and its top 24 mm square for 30 mm. Chisel five 25 mm square mortises through it at 45, 110, 175, 240 and 305 mm from the floor, each turned 90 degrees from the last. Cut five bars from 25 x 50 mm hardwood, as long as the tub allows at their height (179, 174, 170, 165 and 160 mm), and shave each from 25 mm square at the middle out to 50 x 8 mm at the ends. Glue them through the shaft. Fit a hardwood crank 190 mm long with a handle on the square top.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
Çift saplı rendeÇift saplı rende
El TesteresiEl Testeresi
Zımpara KağıdıZımpara Kağıdı
Şerit MetreŞerit Metre
7

The build in 3D

FreeCAD model of this build, the tub, hoops and cover cut through the middle: the three brakes with their openings, the three ledges, and the dasher with its five bars and crank. The dasher was turned through 24 angles.
Tasarım DosyasıBLENDCC0 - Free
8

Churn

Stand the dasher's foot in the step and fill the tub with about 15 litres of heavy cream at about 15 °C, checked with the thermometer, up to the upper bar. Put the cover's halves on round the shaft. Turn the crank steadily the way the ledges face, timing it. When the butter comes, lift the cover and dasher, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema15 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
9

Troubleshooting

Brake-and-ledge churn troubleshooting.

Flow

Loading...
10

History and honest limits

**James Taylor** of Rushville, Schuyler County, Illinois, US 25,453, 13 September 1859, "Churn". He claimed the arrangement of perforated brakes and auxiliary reflectors with a dasher "having its blades flattened out gradually from near the shaft to their ends", and disclaimed the brakes of Hiram Brown's rejected application of 1852 and of M. R. Marcell's patent of 1858. "The number and size of these brakes and ledges depend entirely upon the size and diameter of the tub": the patent gives no sizes, and every size here is ours, as is the crank.

Malzemeler

8

Gerekli Aletler

17

Tasarım dosyaları

1

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...